-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
RF and Microwave: No Black Magic
March 15, 2022 | Andy Shaughnessy, Design007 MagazineEstimated reading time: 5 minutes
I caught up with Ben Jordan after his class on RF and microwave at IPC APEX EXPO. Ben, an electrical engineer, explained how sitting through previous classes on this topic led to him developing his own class. “I wanted to bridge the gap,” he says, “with a class that makes the material approachable and teaches the intuitive nature of fields and waves and how they work in circuit boards.”
Andy Shaughnessy: Ben, I caught your class on RF and microwave. But you also have your own business, correct?
Ben Jordan: Yes, I do.
Shaughnessy: That’s great. Hanging out your own shingle and all that.
Jordan: I’ve actually had it as a side gig for about 10 years but didn’t do much with it. It started when, 11 years ago, I wrote an article for a hobbyist magazine called Elektor Electronics on power supply design. I wanted to release it and suddenly people wanted to buy a kit from me. Hobbyists from Europe were sending me orders, so I had to quickly ramp up and produce little electronic kits. I’m not doing that now because that’s not scalable, but I needed a business entity.
Shaughnessy: That’s very cool.
Jordan: I’ve been doing a little bit here and there, and whenever I train or teach at IPC, like this week, I can be paid through my business. But now I’m looking at making a change, hanging out my shingle as you said, and pursuing the business that will be more financially stable as well as give me time to pursue some of my more creative interests, like music.
Shaughnessy: Yes, exactly. So, tell me a little about the class I attended and some of the challenges you wanted to address with that.
Jordan: So, I’ve sat in on some great RF microwave classes in the past. Rick Hartley has a fantastic one; it’s dense. They’re all good. I studied electrical engineering and I’m a qualified engineer originally, but I never professionally did RF and microwave. I wanted to start doing it because everything is connected wirelessly now. I went back to all my old engineering texts to review the material I studied in university. There’s a lot of math and a lot of theory, but what I discovered is that none of it talked about printed circuit boards beyond, “This is a stripline and this is a microstrip and this is how you determine the impedance.”
I realized something was missing in our community. There are many PCB designers who may not even be degree qualified and believe they can’t do RF and microwave board design because they’ve never been trained in microwave engineering. I would often hear that people see it as some kind of black magic, like, “Those are the wizards in the office down in the corner.” I wanted to bridge the gap with a class that makes the material approachable and teaches the intuitive nature of fields and waves and how they work in circuit boards. How do they work? What’s the effect on the materials and how you actually design the shapes and decide what size they should be for things like filters and impedance matching of circuits?
That grew into another class I developed for antenna design; we have a lot of animations showing the right visualization of how the different types of circuit board antennas work so people can understand them and then dimension them correctly for the target purpose.
Shaughnessy: A lot of it is counterintuitive to a typical design. A PCB designer doesn’t want things to be an antenna, but in RF you do.
Jordan: Some you do and some you don’t. By learning antenna theory, you can also learn how to be a better signal integrity aware digital designer as well because exactly the same principles apply. For example, at the end of my class yesterday, I was showing a design of a slot antenna on a printed circuit board. It’s essentially an impedance-controlled trace with a very specially-sized notch on one side of the board in a plane; that’s an opening. On the other side, you have the micro strip that crosses over the notch with a precise length. But what happens at the frequency of resonance is that it causes very good radiation. It’s a great antenna.
Just at the moment I was showing this, Insulectro’s Mike Creeden stuck his head into the classroom, raised his hand, and said, “This is also why you don’t cross ground planes in a digital design. You’ve just created an antenna without realizing it.” So, yeah, it’s very good. I find that the attendance of my subject is usually pretty good, even in these times when a lot of people still aren’t coming to shows yet.
Shaughnessy: What advice would you give to someone who’s getting into wireless and having to deal with the audio, the analog. You must deal with analog digital, mixed signal, and all this good stuff.
Jordan: There are books of advice, but I would just not to be overwhelmed and don’t keep telling yourself it’s black magic. You can do it if you think you can. Just start on the road, watch the RF and microwave series I did a few years ago as an intro.
Shaughnessy: Is that on YouTube?
Jordan: It was on the Altium YouTube channel because I was working for Altium at that time. I’m not anymore, obviously, but start there. Because we talk about materials, the basic principles and the mathematics are not hard. I’m not trying to teach people how to write their own software to do finite difference time domain or FEM.
There are plenty of software companies that have really dialed that in. There are even a lot of free open-source tools, which I talk about in my class, that do it well. And of course, moving forward with my own company, I will be focusing on turning this into a more staged, in-depth course. There will be more actual design examples so that you can build something yourself, have something that works, and understand how it’s working. That’s my goal for this year.
Shaughnessy: I like your advice: Don’t be overwhelmed by it.
Jordan: That’s right, just start. The journey of a thousand miles starts with one step.
Shaughnessy: Thank you for talking with me.
Jordan: Thank you, Andy. Good talking to you again.
Suggested Items
Connect the Dots: Designing for Reality—The Pre-Manufacturing Process
05/08/2024 | Matt Stevenson -- Column: Connect the DotsI have been working with Nolan Johnson on a podcast series about designing PCBs for the reality of manufacturing. By sharing lessons learned over a long career in the PCB industry, we hope to shorten learning curves and help designers produce better boards with less hassle and rework. Episode 2 deals with the electronic pre-manufacturing process. Moving from CAD (computer-aided design) to CAM (computer-aided manufacturing) is a key step in PCB manufacturing. CAM turns digital designs into instructions that machines can use to actually build the PCB.
Indium Corporation to Showcase HIA Materials at ECTC
05/07/2024 | Indium CorporationAs an industry leader in innovative materials solutions for semiconductor packaging and assembly, Indium Corporation® will feature its advanced products designed to meet the evolving challenges of heterogeneous integration and assembly (HIA) and fine-pitch system-in-package (SiP) applications at the 74th Electronic Components and Technology Conference (ECTC), May 28‒31, in Denver, Colorado.
Siemens Delivers New Solido IP Validation Suite
05/07/2024 | SiemensSiemens Digital Industries Software introduced Solido™ IP Validation Suite software, a comprehensive, automated signoff solution for quality assurance across all design intellectual property (IP) types, including standard cells, memories and IP blocks.
Altair Acquires Research in Flight, Forging a New Path for Aerodynamic Analysis
05/07/2024 | AltairAltair a global leader in computational intelligence, announced it has acquired Research in Flight, maker of FlightStream®, which provides computational fluid dynamics (CFD) software with a large footprint in the aerospace and defense sector and a growing presence in marine, energy, turbomachinery, and automotive applications.
Happy’s Tech Talk #28: The Power Mesh Architecture for PCBs
05/07/2024 | Happy Holden -- Column: Happy’s Tech TalkA significant decrease in HDI substrate production cost can be achieved by reducing the number of substrate layers from conventional through-hole multilayers and microvia multilayers of eight, 10, 12 (and more), down to four. Besides reducing direct processing steps, yield will increase as defect producing operations are eliminated.