-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
IPC Statement on NDAA Provisions Aimed at Bringing Resiliency and Security to Supply Chains
September 16, 2020 | IPCEstimated reading time: 2 minutes
IPC, the global association of electronics manufacturers, issued a blog post in support of the FY 2021 National Defense Authorization Act (NDAA) provisions that would bolster the resiliency and security of the electronics manufacturing ecosystem, including printed circuit board (PCB) fabrication and printed circuit board assembly (PCBA), the green-and-gold hardwiring at the core of all electronics systems. These provisions, approved in both the U.S. House and Senate, aim to improve the security of electronics purchased by the Defense Department. Excerpts from the blog post argue the following:
“The NDAA provisions aim to improve the security of electronics purchased by the Defense Department by developing an affirmative list of allied, trusted countries from which the DoD can source those boards and assemblies. The United States should not be sourcing electronics for national security systems from countries it deems a current or potential security threat. Nor should any other country, for that matter.
“Today, without this requirement, there are potential national security risks associated with systems that are built with PCBs and PCBAs from sources that are beyond the visibility of the DOD. These risks have been well-documented by the Defense Department and outside experts.
“The opposition fears the new requirements will disrupt their established supply chains in countries that are not affirmatively covered. But the provisions explicitly authorize the Secretary of Defense to add countries to the list of locations from which PCBs and PCBAs can be sourced. And, with over $10 billion of PCB manufacturing today in allied countries and the U.S., there is ample capacity today to meet DoD demand for military and commercial off-the-shelf electronics.
“In addition to down-stream electronics industry support, the provisions have over four dozen supporting members of Congress from both sides of the aisle in the House and the Senate. Not a single member of Congress has risen in opposition.
“Moreover, both the full House and Senate have voted to include these provisions in the bill, so in keeping with committee precedent, the broad parameters of issue are settled.
“The NDAA provisions offer the ancillary, but meaningful, benefit of strengthening supply chain resiliency by growing the market for electronics manufactured in the United States and its allies. In fact, U.S. CEOs have indicated a desire to grow their manufacturing operations in the United States but are hedging for the moment. They are waiting for the passage of the NDAA and the demand signal it will send.”
To read the full blog post, visit IPC.org.
Suggested Items
Book Excerpt: The Printed Circuit Assembler’s Guide to... Factory Analytics
04/24/2024 | I-Connect007 Editorial TeamIn our fast-changing, deeply competitive, and margin-tight industry, factory analytics can be the key to unlocking untapped improvements to guarantee a thriving business. On top of that, electronics manufacturers are facing a tremendous burden to do more with less. If you don't already have a copy of this book, what follows is an excerpt from the introduction chapter of 'The Printed Circuit Assembler’s Guide to... Factory Analytics: Unlocking Efficiency Through Data Insights' to whet your appetite.
Listen Up! The Intricacies of PCB Drilling Detailed in New Podcast Episode
04/25/2024 | I-Connect007In episode 5 of the podcast series, On the Line With: Designing for Reality, Nolan Johnson and Matt Stevenson continue down the manufacturing process, this time focusing on the post-lamination drilling process for PCBs. Matt and Nolan delve into the intricacies of the PCB drilling process, highlighting the importance of hole quality, drill parameters, and design optimization to ensure smooth manufacturing. The conversation covers topics such as drill bit sizes, aspect ratios, vias, challenges in drilling, and ways to enhance efficiency in the drilling department.
Elevating PCB Design Engineering With IPC Programs
04/24/2024 | Cory Blaylock, IPCIn a monumental stride for the electronics manufacturing industry, IPC has successfully championed the recognition of the PCB Design Engineer as an official occupation by the U.S. Department of Labor (DOL). This pivotal achievement not only underscores the critical role of PCB design engineers within the technology landscape, but also marks the beginning of a transformative journey toward nurturing a robust, skilled workforce ready to propel our industry into the future.
Winner of The Science Show Rakett 69 Receives Incap Scholarship
04/24/2024 | IncapThe winner of the Rakett 69 science show, Andri Türkson, who stood out as an electronics enthusiast, received a scholarship from Incap Estonia, along with an internship opportunity in Saaremaa.
Alternative Manufacturing Inc. Awarded QML Requalification to IPC J-STD-001 and IPC-A-610
04/24/2024 | IPCIPC's Validation Services Program has awarded an IPC J-STD-001 and IPC-A-610 Qualified Manufacturers Listing (QML) requalification to Alternative Manufacturing Inc (AMI).