-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueBreaking High-speed Material Constraints
Do you need specialty materials for your high-speed designs? Maybe not. Improvements in resins mean designers of high-speed boards can sometimes use traditional laminate systems. Learn more in this issue.
Level Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
TTM: Consult Fabricators Early for PCB Designs
July 2, 2015 | Andy Shaughnessy, PCBDesign007Estimated reading time: 6 minutes
Shaughnessy: It looks like something that would make a fabricator say, "Are you serious?"
Ellis: The industry has changed tremendously since I started in it, that's for sure. I used to wire wrap assemblies when I was a kid.
Shaughnessy: In your talk, you mentioned how everyone talks about drilling vias below six mils. But then you point out that six mils is only two times the width of a human hair.
Ellis: Yes. I feel like I’m always splitting hairs when I build fine-pitch stack-ups, because they require trade-off analysis between minimum aspect ratio, hole sizes, pad and antipad sizes, the space left between those pads, and how many traces can be run between the pads, if any. 6 mils is the smallest mechanical drill size we’ll use in North America, and it’s only the diameter of 2 human hairs and smaller than a hypodermic needle. Because 6 mil drill bits break easily, can’t be re-sharpened, and are very expensive, Asia sites rarely use them. So I never design a stack-up for our China sites using a 6 mil drill. But as hole size increases, so do the pad diameters in order to maintain annular ring requirements, and that can kill the routing space between pads.
Come to think of it, another thing I would like to see engineers do more often is consider the production site technical capabilities. Offshore PCBs are significantly lower in cost, because they’re optimized for continuous processes that don’t need to be interrupted or require highly advanced, but slow, equipment or processes. Asia sites have excellent capabilities, but they are not all at extreme tech levels of some of our N. America sites. So designs should be done in accordance with production site guidelines and available materials.
Shaughnessy: Sure. Well, it was a great talk. You covered a lot of really cool cutting-edge stuff. The designers in the crowd really enjoyed it.
Ellis: Thank you.
Shaughnessy: Thank you, Julie. I appreciate your time.
Page 2 of 2Suggested Items
DuPont Showcases AI Innovations Featuring Advanced Interconnects at 2024 International Electronic Circuits Exhibition
05/13/2024 | DuPontDuPont announced it will showcase its comprehensive range of advanced circuit materials and solutions at the 2024 International Electronic Circuits Exhibition in Shanghai. With a product portfolio that includes fine line, signal integrity, power and thermal management, DuPont will exhibit at Booth #8L06 at the National Exhibition and Convention Center (NECC) from May 13 to 15.
MKS’ Atotech to Participate in ECTC
05/10/2024 | MKS’ AtotechAt this year’s 74th IEEE Electronic Components and Technology Conference (ECTC), MKS’ Atotech will present and demonstrate its latest product and service innovations.
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.