-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Simplifying Your Design
November 9, 2023 | I-Connect007 Editorial TeamEstimated reading time: 1 minute
It’s safe to say that millions of dollars, not to mention man-hours, are wasted each year because of over-constrained, overly complicated PCB designs. Much of this is due to the increase in signal speeds and rise times, even in “mature” PCBs, and the extra cost is already part of the budget.
For this issue on simplifying PCB designs, the I-Connect007 Editorial Team spoke with IPC instructor Kris Moyer about ways that designers can avoid overconstraining their designs and making them needlessly complex. As Kris says, streamlining your design comes down to having a solid understanding of fab and assembly processes and the silicon tradeoffs that can simplify or overcomplicate your design, as well as the need to start working with fabricators early in the cycle.
Andy Shaughnessy: What are some typical snafus and missteps that you see designers make to overcomplicate their designs?
Kris Moyer: Here’s what often happens: Let’s say you have one connector on your board that needs tight tolerance. But rather than dimensioning to just that connector, locally, designers will do a tight tolerance to the data from the global dimensioning system, which now constrains the entire board.
Or, if they need perfect coplanarity on a BGA part for good BGA mounting, they’ll put co-planarity back over the entire board where they don't need it, because regular chips, gull-wings, and so on don't need the same amount of coplanarity as a BGA—or they'll try to hold layer tolerances: “I need a 2-mil layer plus or minus 10%,” because they know that 10% is normal for tolerance, but they missed the part of the spec that says 10% or 1 mil, whichever is greater. Fabricators can't hold that tight a layer-to-layer tolerance when it's below a certain layer thickness.
Below about a 10-mil thickness, the best fabricators can do layer-to-layer is 1 mil for nominal processing; If you want to hold a tighter tolerance, you're paying for 100 to get five boards. That’s just a couple of examples. Another is overly tight hole tolerances: “I want to have 150-mil diameter hole ±1 mil.” Again, it's unreasonable, right?
To read the rest of this interview, which appeared in the November 2023 issue of Design007 Magazine, click here.
Suggested Items
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Happy’s Tech Talk #27: Integrated Mesh Power System (IMPS) for PCBs
04/08/2024 | Happy Holden -- Column: Happy’s Tech TalkA significant decrease in HDI substrate production cost can be achieved by reducing the number of substrate layers from conventional through-hole multilayers and microvia multilayers of eight, 10, 12, and more to only two layers. Besides reducing direct processing steps, the yield will increase as defect-producing operations are eliminated. The integrated mesh power system (IMPS) was invented in the latter years of MCM-D use for thin-film fabrication. Those geometries fit today into our use of ultra HDI.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
Now Available: Episode 4, Season 2 of Designing for Reality—Lamination
04/04/2024 | I-Connect007I-Connect007 has just released the latest episode of its podcast series, On the Line With..., which focuses on designing for reality in the electronics industry. Multilayer boards bring along a completely different set of processes. In this installment, ASC Sunstone VP/Manager Matt Stevenson discusses manufacturing techniques for multilayer boards. Of course, this necessitates a review of drill and registration techniques, followed by the ins and outs of lamination.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.