Chris Hanson: New Ventec IMS Dielectrics Rated for Higher Temps
Andy Shaughnessy recently spoke with Chris Hanson, global head of IMS Technology for Ventec International Group. During their conversation, Chris discusses his group’s recent efforts to create new IMS materials, with a focus on dielectrics. As Chris explains, Ventec has developed several new dielectrics that can withstand much higher operating temperatures, one of which is UL-rated for a maximum operating temp of 155°C, which may be the highest for an IMS dielectric.
Ventec Book Excerpt: Thermal Management with Insulated Metal Substrates
The following is an excerpt from Chapter 1 of "The Printed Circuit Designer's Guide to... Thermal Management with Insulated Metal Substrates," written by Ventec International Group’s Didier Mauve and Ian Mayoh. In this free eBook, the authors provide PCB designers with the essential information required to understand the thermal, electrical, and mechanical characteristics of insulated metal substrate laminates.
This Month in Design007 Magazine: Mentor—Managing Small Problems for Profitability
At DesignCon, I met up with Todd Westerhoff, product marketing manager for highspeed design at Mentor, a Siemens Business, to discuss common design profitability issues and cost-aware PCB design. He explains how simple problems can “slip through the cracks” and cause delays, what you can do, and how first-order analysis can make simulation accessible to designers who wouldn’t simulate otherwise.
IPC APEX EXPO 2020 Attendees Speak: Caleb Buck
"I am a PCB designer and an electrical engineer," said Caleb Buck of EaglePicher Technologies. "I’m not involved in the manufacturing, but I tell manufacturers what to do via my drawings. I had an interest in learning more about the IPC standards, my manufacturer’s capabilities, and some of the tools they use."
Meet Eran Navick, I-Connect007 Columnist
Meet Eran Navick, one of I-Connect007’s newest columnists! In his columns, Eran will discuss technology around the world, touching on all aspects of PCB technology, especially high technology. Eran has been in the PCB business for over 25 years and held key positions in PCB companies, including as a PCB designer and applications engineer.
Meet John Watson, I-Connect007 Columnist
Meet John Watson, CID, one of our newest I-Connect007 columnists! John has been in the electronics industry for 40 years, with 20 of them being in PCB design, and is now a senior PCB engineer for Legrand Corporation. Read "Elementary, Mr. Watson" in Design007 Week Newsletter.
The World of PCBs: Anything But Boring
Andy Shaughnessy had the chance to catch up with Megan Teta, CID+, product manager of design and education services at Insulectro. Megan explains why she’s excited to become more involved in training and why the world of PCBs is anything but boring, contrary to popular opinion.
Digi-Key on Adapting to the Changing Industry Landscape, Part 2
The I-Connect007 editorial team recently spoke with Chris Beeson, executive vice president of global suppliers and new business development at Digi-Key Electronics, about trends and the changing landscape of the industry. In the second half of this interview, Beeson discusses the EDA tools market, and how Digi-Key works with PCB designers to present the most efficient, seamless process for selecting components.
A Radical New Design Perspective
Nolan Johnson recently interviewed Gordon Kruberg, CEO of Gumstix, which was acquired by Altium recently. While Gumstix designs and sells computer hardware products, Altium bought Gumstix for the Geppetto design software. Gordon discusses how the concepts of Geppetto are likely to influence future design methods in the Altium environment.
Book Review: The Printed Circuit Designer’s Guide to…Executing Complex PCBs
If you are serious about designing complex PCBs (most designs today are far from elementary) and even more serious about doing it right the first time, then this is the book for you. Loaded with guidelines for designing cutting-edge PCBs, this book is filled with real-world examples and tips, tricks, and techniques by some of Freedom CAD’s most experienced designers.
Dugan Karnazes Discusses His New Startup
I caught up with Dugan Karnazes again this year and discussed his new startup, Velocity Research, which is a one-stop shop for design made up of technical creatives. The Grand Rapids company is already doing design work for a variety of customers, from individuals to multinational companies.
IPC-2581 Continues to Flourish
Because standards adoption in this industry tends to be akin to turning around a battleship, what is often seen as new has generally already been in production for 10 years or more. Often, there are outside influences and dependencies that cause this, so most of us tend to take a “wait-and-see” approach—let others shake out the issues. And even then, we only look at adoption if the mandate comes from higher-ups in the organization. It works the way we do it now, so why change?
So Many Standards Committees, So Little Time
During the IPC Summer Meetings and Panelpalooza in Raleigh, North Carolina, I met with Leo Lambert, vice president and director of technology at EPTAC. We discussed IPC’s recent efforts to revamp the way standards are developed and interpreted as well as changes to training and education committees and a variety of methods for eliminating errors and duplicated comments when revising standards.
Leo Lambert on Training the Next Generation of Technologists
I sat down for an interview with Leo Lambert, VP of technical director for EPTAC Corporation, during the IPC Summer Meetings in Raleigh, North Carolina. We discussed the company’s growth, including plans to have training centers across different regions of the country to help cut down on students’ travel times, and why training methods must constantly evolve to remain effective.
Insulectro and DuPont Experts Talk Flex Design
I recently spoke with Insulectro’s Chris Hunrath and DuPont’s Steven Bowles at the DuPont Technology and Innovation Center in Sunnyvale, California. We discussed a variety of topics related to flex design, including the support structure that’s needed in flex design, the everchanging world of flex materials, and the need for working with a flex fabricator as early as possible in the flex design cycle.
SimplifyDA’s Floorplanning Tool Optimizes Autorouting
Zen Liao, CEO of Simplify Design Automation, recently spoke with the I-Connect007 editorial team about his company’s high-level floorplanner for autorouting, which allows engineers to pass their ideas along to PCB designers. Zen discusses the floorplanning technology and his marketing strategies as well as the challenge of getting reluctant PCB designers to embrace autorouters.
Focusing on Surface Sensitivity for Reliability
At the recent IPC High-Reliability Forum and Microvia Summit, Customer Applications Scientist Elizabeth Kidd and Sales Engineer Alex Bien, both of BTG Labs, discuss with Andy Shaughnessy their presentation on the challenges of working with highly sensitive surfaces, such as the risk of contamination. They also talked about the various surface characterization techniques that BTG Labs uses to identify such contaminants.
IPC Reliability Forum Wrap-up With Brook Sandy-Smith
I attended the recent IPC High-Reliability Forum and Microvia Summit in Baltimore, Maryland. The speakers and panelists focused on a variety of topics, but one issue that kept popping up was the failure of some microvias on military and aerospace PCBs. Fortunately, some smart technologists are focusing on determining the cause of these via failures. I asked Brook Sandy-Smith, IPC’s technical education program manager, to give us a quick wrap-up of this event.
IPC High-reliability Forum and Microvia Summit Review, Part II
The Microvia Summit on May 16 was a special feature of the 2019 event in Baltimore, since microvia challenges and reliability issues have become of great concern to the PCB manufacturing industry. It provided updates on the work of members of the IPC V-TSL-MVIA Weak Interface Microvia Failures Technology Solutions Subcommittee and opportunities to learn about latest developments in methods to reveal and explain the presence of latent defects, identify causes and cures, and be able to consistently and confidently supply reliable products.
Mentor Tools: Optimized for Flex and Rigid-flex Design
With the launch of the new Flex007 section in Design007 Magazine, we asked David Wiens, product marketing manager with Mentor, a Siemens Business, to tell us about their tools’ flex and rigid-flex design capabilities. As David explains, today’s higher-end design software tools are optimized for flex design, making workarounds a thing of the past.
26 Meters of Flex!
Barry Matties spoke with Philip Johnston, managing director of Trackwise Designs, about the company’s patented length-unlimited multilayer printed circuits aimed at replacing conventional wire harnesses. Originally created for the aerospace industry, Trackwise has since seen growing interest from a number of different industries. Jake Kelly, managing director and chairman of Viking Test Ltd., also joined the conversation to discuss the importance of having a flexible equipment supplier when dealing with such a unique technology.
Design Is a Pivotal Piece of the Puzzle
As a field applications engineer at TTM Technologies, which has fabrication and manufacturing locations around the world, Julie Ellis sees a wide variety of customer design requirements. In this interview with the I-Connect007 Editorial Team, Julie explains how PCB designers can influence the development of the PCB. She shares a variety of tips and tricks that designers can implement early in the design process to help optimize fabrication and assembly later on and keep small issues from becoming big problems downstream.
Design for the Unknown
Our industry loves DFx, also known as the “Design Fors.” As PCB designers, we not only design for manufacturability (DFM) but we design for assembly, reliability, cost, test, and many more factors which we like to lump together as DFx. But now, I think it’s time we embrace a new DFx: Design for the Unknown, or DFU.
Stitching Capacitor: Crosstalk Mitigation for Return Path Discontinuity
When the return path is broken due to the switching of reference planes with different potential, e.g., from ground to power or vice versa after layer transition on PCB, the return current might detour and propagate on a longer path, which causes a rise in loop inductance. This might lead to the sharing of a common return path by different signals that pose a high risk of interference among the signals due to higher mutual inductance. This interference results in signal crosstalk. To mitigate the crosstalk due to return path discontinuity (RPD), stitching capacitors are mounted on the PCB to serve as a bridge between the two reference planes of interest on different PCB layers.
Altium’s Craig Arcuri on Design Rules: Past, Present, and Future
We recently spoke with Altium’s Craig Arcuri about his views on design and manufacturing rules. Craig has experience running both design and manufacturing companies, so he has a fairly circumspect view of constraints from both sides of the product realization process. Craig details some of the challenges with setting and managing hundreds of often divergent design and manufacturing rules, and how both design and manufacturing constraints need to evolve.
Smart Design Data Is Essential for Industry 4.0 Manufacturing
Almost all of the conversation regarding Industry 4.0 is centered on the manufacturing floor, which is where the effect of the initiative is most felt initially. Little attention is given to the starting data for manufacturing—the data that comes from design. However, you can’t have smart manufacturing if your process begins with dumb data. As Pink Floyd said, “You can’t have your pudding if you don’t eat your meat!”
Words of Advice: Long Component and Laminate Lead Times
In a recent survey, we asked the following question: What advice do you have regarding the current supply chain issues? Here are just a few of the answers, edited slightly for clarity. One reply really sticks out: "If the end customer is large, use their power."
George Fox University: Teaching PCB Design to EE Students
Gary Spivey is director of engineering projects at George Fox University, a Christian college in the Pacific Northwest, and his students learn to design and fabricate a PCB while also giving back to the community. Not surprisingly, these graduates get snapped up quickly. In this wide-ranging interview, Spivey discusses GFU’s engineering curriculum, their cutting-edge lab facilities, and the need to teach students to think critically.
From Spain to Austria: A Student’s Drive to Be a Professor
The AltiumLive event in Munich drew several hundred PCB designers from around Europe, including engineering students interested in PCB design. I spoke with Pablo Sanchez Martinez, a student at FH Joanneum in Austria who is working toward being a full professor in hardware design. Pablo discussed his studies in engineering and PCB design, the classes he’s teaching, and his plans for teaching the young engineers of the future.
Sunstone's Terry Heilman Discusses the Evolving Industry
For the last 14 years, CEO Terry Heilman has been one of the key leaders in driving the expansive growth at Mulino, Oregon-based Sunstone Circuits, growing from a traditional PCB manufacturer to a PCB solutions provider with online ordering and a free PCB design tool. At IPC APEX EXPO 2019, Terry discusses the importance of serving the customer, how customers are shaping companies today, and the impact this will have on companies in the future.
Andy Johnson: EDA a Great Field for Young People
At the AltiumLive event in Munich, Germany, I sat down for an interview with Altium’s Andy Johnson. Andy is 25 and just a few years out of college, so I asked for his thoughts on working in this industry and what we can do to draw more young people into the PCB design community.
Kelly Dack at IPC APEX EXPO: The Attendees Speak!
During IPC APEX EXPO, Guest Editor Kelly Dack and the I-Connect team roamed the show floor, recorders in hand. They asked various attendees for their impressions of the show, and any new tools and technology that may have caught their attention. These are their stories.
Dan Gamota Discusses Flex and Alternative Substrates
As the VP of manufacturing technology and innovation for Jabil, Dan gave us his take on the current state of flex and alternative substrates and explained why modeling, automation, and process controls are likely to be key ingredients in the recipe for manufacturing non-FR-4 boards in the future.
Nano Dimension Offers Update on Dragonfly 3D Printer a Year After Launch
The Nano Dimension Dragonfly 3D printer arrived in much fanfare a little over a year ago. The company has been selling them to customers around the world, many of whom are using them to print antennas, sensors, and PCBs. At AltiumLive in Munich, I asked Product Manager Robert Even to discuss what they’ve learned in the year since the Dragonfly debuted, and some potential uses for 3D printing technology.
3DEM Modeling: Influence of Metal Plating on PCB Channel Loss and Impedance
This article briefly introduces different types of metal plating commonly used in PCB fabrication. Subsequently, the influence of metal plating on PCB channel loss (i.e., insertion loss or S21) and impedance (i.e., time domain reflectometry or TDR) is studied with 3DEM modeling,
Mentor’s Cristian Filip Discusses His Award-winning DesignCon Paper
During DesignCon, I met with Cristian Filip, a senior product architect with Mentor, a Siemens business. Cristian had just received word that his paper had won a DesignCon Best Paper award—his second such award in three years. I asked Cristian to discuss his paper and how this technology can help improve manufacturing yields at high volumes.
Cherie Litson on ECAD/MCAD and Training the Next Generation
Cherie Litson, CID+, was one of the instructors at AltiumLive Munich. I asked her to discuss some of the topics she covered in her class, and what the future of PCB design will look like. How are we going to pass down all of this design knowledge to the next generation?
RTW IPC APEX EXPO 2019: Judy Warner on Altium's Transformative Vision
During IPC APEX EXPO, Guest Editor Kelly Dack sat down for an interview with Judy Warner, Altium's director of community engagement. They discussed Altium's efforts to educate PCB designers, regardless of their CAD tools, and the company's plan to transform the industry by bringing together PCB design and manufacturing.
The Electronic Component Shortage Crisis: A Veteran Engineer’s Perspective
From where we stand now, at the beginning of 2019, we see lead times for some components in the short range of up to 16 weeks; medium-to-high is 32 weeks, and long lead times are as far out as 80 weeks. In other words, if we ordered a component today, it would arrive in over a year a half from now (maybe). This all started with the capacitors (we will see why later), but we now see other component series being sucked into this problem.
A Drone's-eye View of the IPC APEX EXPO Show Floor
If you couldn't make it to IPC APEX EXPO in San Diego, don't worry. We have full coverage of this annual must-attend event, from the opening ceremony to the close of the final day. To get a sense of the size of this year's show, check out our drone's-eye view of the show floor. Can we name our drone Air007?
TUM Hyperloop Team Learns PCB Design on Way to Setting World Speed Record
At AltiumLive Munich, I met with Tobias Bobrzik, a Technical University of Munich student and member of the TUM Hyperloop team. In 2018, the TUM Hyperloop team’s prototype pod set the world speed record of 290 miles per hour, which lead to their meeting with Musk. Tobias designed some of the PCBs used in that vehicle, so I asked him to tell us more about this experience, and what he hopes to do after graduation.
CES 2019: More Show Floor Favorites
In my final piece covering CES 2019, I will review more automotive technology, updates on 3D printing, and some trending devices such as smartwatches and new computer components for those that either need or just want to have extremely powerful and impressive-looking computers.
AltiumLive Munich: Day 2 Keynotes
Having enjoyed the conference dinner and robot battles of the previous evening, a good night’s sleep, and a hearty breakfast, Altium’s family of over 220 electronics engineers and designers eagerly returned to the conference room. Many jostled to secure the best seats for the second day of the European AltiumLive design summit in Munich, keen to make the most of the “learn, connect, and get inspired” opportunity it offered.
Happy Anniversary, Gerber Format: Looking Ahead to Digital Innovation
This year, we celebrate the 55th anniversary of the introduction of the Gerber machine language format. We can thank H. Joseph Gerber, the man who took manual PCB design to the next level with the automated photoplotter, for giving us this format in 1964. Gerber immigrated to the United States in 1940 with his mother following the death of his father during the Holocaust. Gerber started Gerber Scientific Instrument Company in 1948 to commercialize his first patented invention—the variable scale.
CES 2019 Showstoppers, the Show Floor, and Some Neat Stuff
CES 2019 is over, and those of us who spent four to five days trying to see and hear as much as possible are in recovery mode. There were over 182,000 attendees, and 6,600 of us were media all trying to get to as much of the 2.9-million-square-feet exhibit space as possible.
Mentor and Seica Partner for Data Prep and Testing Big Boards
Mark Laing, business development manager of the Valor division at Mentor, a Siemens company, and Luca Corli, director of sales at Seica, speaks with I-Connect007 Technical Editor Pete Starkey about the partnership between their two companies, which enables efficient data preparation for testing big boards, and accelerates new product introduction (NPI) cycles.
Robert Art on the Importance of Thermal Management
Robert Art, global account manager for IMS materials at Ventec International Group, discusses future market requirements for thermal management materials, the need for a better understanding of the concept of thermal impedance, and an initiative to propose a consistent industry-standard method for measuring thermal conductivity while at electronica 2018.
Top 10 Most-Read PCB Design Articles of 2018
Every year, we like to take a look back at the most popular PCB design news, articles, interviews, and columns. Without further ado, here are the top 10 most-read PCB design articles from the past year. Check them out.
In Medical PCB Design, Innovation Never Stops
Medical electronics is an exciting field to be working in right now with new ideas coming online almost daily. We last interviewed medical PCB designer Kenneth MacCallum in 2015. Recently, I asked him to give us an update on trends he sees in medical electronics, and some of the challenges in adapting the latest technology to this segment of the industry.
Randy Burcham Discusses New Techniques for BOM, Daughterboards
During AltiumLive, I spoke with IOTA Engineering's Randy Burcham, who taught several classes during the event. He explained his methodology for filtering BOM data as well as his new approach to working with daughterboards and how he was up and running on Altium tools after only three days.
Stephen Chavez: Breaking the Design Data Bottleneck
When we started planning this issue on design data, I knew we’d have to speak with PCB designer and EPTAC design instructor Steph Chavez. In this interview, he explains some of the biggest issues related to good design data handoff, and he offers some ways forward.
At GreenSource, Lean and Green Starts on the Front End
GreenSource is the first new captive shop in American in decades, and one of the first waste-free board shops as well. The CAM engineers all work remotely, and they can launch a job without ever entering the facility. I spoke with JanNell Taylor and Andy Schilloff, who work at the CAM office in New York. We discussed what it’s like working for a company that plays by its own rules, and what they're doing to get ready for the day GreenSource goes commercial
Life Beyond 10 Gbps: Localize or Fail!
Ideally, all interconnects should look like uniform transmission lines (or wave-guiding structures) with the specified characteristic impedance. In reality, an interconnect link is typically composed of transmission lines of different types (microstrip, strip, coplanar, coaxial, etc.) and transitions between them such as vias, connectors, breakouts and so on. Transmission lines may be coupled to each other that cause crosstalk. The transitions may reflect and radiate energy due to discontinuities in signal and reference conductors. The crosstalk, reflections and radiation cause unwanted and sometime unpredictable signal degradation.
PCB Carolina 2018 Draws a Crowd of Technologists
PCB Carolina 2018, the one-day tabletop show based in Raleigh, North Carolina, drew quite a crowd to the McKimmon Conference and Training Center at NC State University on November 7. Show managers Tony Cosentino, Randy Faucette, and Lance Olive (all employees of the Better Boards service bureau) said that this year’s event showed signs of growth compared to the 2017 show, which was also larger than the previous year. They estimated that about 1,000 people attended this year, and they expect another increase in attendance in 2019.
Darwin E. George: Seeking PCB Design Job at Retirement Age
Some of us dream of living a life of leisure at 70. But not Darwin E. George. This septuagenarian wants to find a job designing PCBs. We met up with Darwin at AltiumLive, where he was networking and trying to get his foot in the door with one of the companies that are hiring now. Darwin told us about his career in PCB design, his experience learning a new EDA tool, and why he would rather design high-speed PCBs instead of playing shuffleboard for the rest of his life.
Mentor and TEXMAC Takaya Team up to Optimize DFT
At SMTAI, Mark Laing of Mentor, a Siemens Business, and Dave Levine of TEXMAC Takaya, sat down with Editor Nolan Johnson to discuss design for test, and their collaboration to improve DFT in PCB design tools and test machinery. They also traced the evolution of DFT over the past decade as it has begun to "left-shift" farther into the realm of the designer, all the way up to schematic entry.
Simon Fried: Additive Manufacturing Through Printed Electronics
Simon Fried, president of Nano Dimension, discusses how the company has taken the additive manufacturing process to the next level through printed electronics. He also shares his thoughts on the growing demand for 3D circuits, as well as how this could potentially be a game-changer for PCB designers.
Cadence: Bullish on AI
David White has been involved with artificial intelligence research for almost 30 years. Now, David is the senior group director of R&D for Cadence Design Systems, and I knew we’d have to speak with him for this issue on AI. In a recent interview, we discussed his decades of work in AI, Cadence’s research into AI and machine learning, and what he believes AI could mean for the EDA tools of the future.
John R. Watson Returns to AltiumLive in San Diego
When AltiumLive launched last year, John R. Watson, CID, of Legrand signed up as an instructor. He’ll be presenting at this week’s AltiumLive in San Diego as well. I spoke with John recently about his AltiumLive class, and the state of PCB design. He also discussed a few tricks for designing boards with components that are currently on an 80-week lead time, and why this problem is likely to get worse before it gets better.
Artificial Intelligence: More Questions than Answers
I’ve been covering artificial intelligence (AI) and related technologies for years, particularly at events such as the annual Consumer Electronics Show (CES). As I write this, we are in the run-up to CES 2019, and the Artificial Intelligence Conference in San Francisco, so the AI landscape is likely to change—at an ever-accelerating rate. Let’s look at some of the challenges facing AI now, and then after CES 2019 we can take another look.
Help Wanted: PCB Design Layout Specialist
I was told recently that the designer, aka the PCB layout specialist, is a dying breed soon to be extinct. I wish to reassure my fellow designers that, in my opinion, you are in the catbird seat. You are in hot demand and you should have great opportunities for the remainder of your career. By the way, after reading this article, you may feel empowered to go ask for a raise. Please don’t tell your manager that I sent you!
APCT Moves into Rigid-Flex with Cartel, Cirtech Acquisition
When I spoke with APCT President Steve Robinson a year ago, he said he was interested in adding flex and rigid-flex capabilities, and working closely with designers and engineers. With the recent acquisition of Cartel and their subsidiary Cirtech, APCT now has a flex and rigidflex facility, along with military and aerospace certifications. At DesignCon 2018, I asked Steve to discuss these acquisitions and what they mean for APCT and their customers.
Field Trip: CID Class Sees How Flex is Made at Streamline Circuits
While I was teaching my CID class for EPTAC in Santa Clara, I learned that we were only a block away from Streamline Circuits. Streamline does a lot of military and aerospace work, as well as communications and industrial electronics. The company manufactures quite a bit of multilayer flex and rigid-flex circuits, in addition to rigid boards. This would make a great field trip for my CID class!
Experts Discussion: What Does 5G Mean to Materials and EDA Tools?
Whether we’re ready for it or not, 5G technology is coming. We decided to speak with John Hendricks, market segment manager for wireless infrastructure at Rogers Corporation, and Ben Jordan, director of product and persona marketing for Altium, about the challenges related to 5G and what this means for PCB designers and fabricators.
ITEQ Ready for Autonomous and Electric Vehicles of the Future
During DesignCon 2018, I spoke with Tarun Amla, the executive vice president and CTO of ITEQ. We discussed ITEQ’s future plans, including the development of materials for cutting-edge technology needs, such as autonomous and electric vehicles, as well as 5G technology.
Zuken Pulling Ahead in Automotive PCB Design
Zuken has been developing PCB design tools for the automotive market for years. With automotive electronics worth over $200 billion globally, and growing every day, Zuken is preparing for a brave new world of smart cars, and autonomous and electric vehicles. I spoke with Humair Mandavia, chief strategy officer with Zuken, and asked him about the challenges facing automotive PCB designers, and the trends he’s seeing in this constantly evolving segment of the industry.
Martin Cotton Discusses Ventec’s New Book and Low-Loss Materials
During DesignCon 2018, Andy Shaughnessy sat down for an interview with Martin Cotton, director of OEM projects for Ventec. Martin was a PCB designer for years, so he has experience on both sides of the desk. They discussed Ventec’s reasons for coming to DesignCon, their expansion into low-loss materials, and Ventec’s new I-Connect007 book, The Printed Circuit Designer’s Guide to Thermal Management with Insulated Metal Substrates.
Julie Ellis: TTM’s Interface Between Designer and Fabricator
As a field application engineer for TTM, Julie Ellis sees the problems that can occur between circuit board designers and manufacturers. Barry Matties spoke with Julie at the AltiumLive event in Munich about the age-old problem of throwing designs “over the wall,” the trend towards HDI, and what advice she would give new designers.
SnapEDA Harnesses Technology in Providing Verified Parts
Like many young entrepreneurs, Natasha Baker knew she wanted to run her own company years before she finally pulled the trigger. But she waited until the time was right, developed a business plan, and stuck to it. Now, five years after SnapEDA was launched, the company continues to expand its library parts and symbol creation services, with the help of some of today’s most cutting-edge technology. I recently caught up with Natasha, and we discussed how her team utilizes technology that has helped SnapEDA to become a major player in this space.
IoT: Let’s Put the “A” Back into EDA
If I say IoT, most people today will immediately conjure up some notion in their mind. This is especially true in the engineering community, where many of us are hanging the future of our careers on the Utopian vision of a clean, beautiful environment with hidden networks and sensors everywhere.
RTW IPC APEX EXPO: Valor Tool Benefits from Merging Mentor, Siemens Technologies
Oren Manor, director of business development, discusses the convergence of the electrical and mechanical discplines made possible through Mentor's merger with Siemens. Manor also explains how Mentor's Valor platform now utilizes Siemens' "digital twin" concept.
Out-of-the-Box Innovation Strikes a Chord at NAMM 2018
The National Association of Music Merchants (NAMM) holds two shows each year; the first is in Anaheim in January, and the second in Nashville in July. The January show is huge, attracting 100,000 visitors during its four-day run. My friend and editor (and bass player) Dan Feinberg has discussed how difficult it was for him to cover the CES show in a few days, and I must echo that sentiment about NAMM. It is one gigantic show.
Fully Automated Schematic Verification
Schematic verification is a part of the hardware engineer’s responsibility just as PCB layout verification is an accepted part of the PCB designer’s responsibility. However, with today’s circuit designs becoming more and more complex, time-consuming manual schematic verification is no longer an option. Manual verification of a complex circuit introduces significant risk by not identifying schematic design errors that are, in turn, passed to the downstream processes and ultimately to the fabricated board.
What’s New in EDA: The Experts Discussion
We wanted to find out what’s new in the world of EDA. Joining us on our experts conference call were Polar Instruments Managing Director Martyn Gaudion, DownStream Technologies founder Rick Almeida, and Director of Product Management Mark Hepburn and Product Management Group Director of Allegro Enterprise Products Hemant Shah, both with Cadence Design Systems. The group discussed the challenges and opportunities they see in our industry, as well as the need to bring new blood into the PCB design community.
Nano Dimension’s 3D Printing: Prototypes at the Push of a Button?
SICK AG is a global manufacturer of sensors and sensor solutions for industrial applications, with headquarters located in Waldkirch, Germany. After a demo of Nano Dimension’s new 3D printing machine at productronica, Barry Matties met with SICK’s Danny Wernet to discuss its pros and cons and get his overall impression of the technology. Are 3D prototypes really as simple as feeding in a Gerber file and pushing a button?
Thermal Management Update with Doug Brooks
I had the opportunity to talk with our contributor Doug Brooks recently. He has been doing some research on temperature effects on PCB traces over the last few years, and I wanted to check the status of his latest thermal efforts. He discussed his work with Dr. Johannes Adam, why temperature charts based on a trace in isolation are inaccurate, and how the industry remained so wrong about PCB temperatures for so long.
HDI PCBs: Make the Right Choice from Design to Volume
Modern electronic products are expected to offer evermore advanced functions, while the products themselves are becoming increasingly smaller. There are two key factors for the successful production of HDI PCBs: first, making the right choices at the design stage, and then carefully choosing the factory that can support the specific technical demands of the project. NCAB Group COO Chris Nutall explains.
Nancy Jaster Brings Manufacturing, Design Background to Designers Council
Nancy Jaster was recently named the head of the IPC Designers Council. At the recent AltiumLive 2017 event, I spoke with Nancy about her unique background in both design and manufacturing, and how she hopes to use that experience and mindset to revitalize the Designers Council going forward, particularly with the International and student chapters. We also discussed her plans to bring more young people, particularly women, into the industry.
Video from productronica 2017: Karel Tavernier on Ucamco's New Communic8tor
European Editor Pete Starkey and Ucamco Managing Director Karel Tavernier discuss Ucamco’s cloud-based Communic8tor platform which facilitates two-way communication between the CAM engineer and the PCB designer, or any other party involved in the manufacturing process. This gives real-time access to image data and annotations, enabling queries to be resolved, changes to be approved, and a full communications history to be maintained.
AltiumLive Summit—Munich, Germany, Part 2
Pete Starkey continues with his review of the AltiumLive PCB Design Summit held recently in Munich, Germany. The second day commenced with a new product launch. “Working together is hard” it read on the screen. Statistics indicated that 33% of new products were late getting to market, of which 28% were late due to insufficient collaboration, and up to 50% of potential revenue could be lost through being late to market. Then the screen read “NEXUS makes it easy!”
Nine Dot Connects: Good Design Instruction is a True Value-Add
Nine Dot Connects has certainly blazed an interesting trail. The company started out as an Altium reseller, but in less than a decade, Nine Dot Connects has also become a design service bureau and a provider of PCB design instruction, training, and consulting services. I recently interviewed Paul Taubman, technical services director for Nine Dot Connects. We discussed the company’s expansion from VAR to service bureau and content provider, and the changing landscape of PCB design instruction.
AltiumLive 2017 Munich: Sold Out!
I recently sat down with Ted Pawela, Lawrence Romine, and Judy Warner of Altium to wrap up their sold-out AltiumLive 2017 PCB Design Summit in Munich, Germany. This conference, following on the heels of an AltiumLive event in San Diego, was packed full of PCB designers who attended a series of great keynotes and an excellent technical program. We discussed some of the highlights of the show, including designers’ reactions to a new version of Altium Designer 18 and the brand-new Altium Nexus tool.
Polar Instruments’ Martyn Gaudion Discusses Tools and Books
Polar Instruments has pretty been busy lately. In the last year, Managing Director Martyn Gaudion has written two books for I-Connect007, and the company has been working to upgrade its tools, especially library functionality. I met with Martyn at PCB West. We discussed Polar’s newest tool updates, Martyn’s new side job as an author of technical books, and the continuing growth of the EDA segment, including among young people.
Sensible Design: Thermal Management—The Heat is On
Thermal management materials are designed to prolong equipment life and reduce incidences of failure. They also maintain equipment performance parameters and reduce energy consumption by reducing operating temperatures, and minimising the risk of damage to surrounding components. Indirectly, they maintain brand reputation, as the reliability of the equipment will be very dependent upon the effectiveness of the thermal management technique used.
Whose Fault is That Bad Board?
Years ago, I held a position in an EMS company where projects were analysed before manufacturing. We found that even some of the best and most innovative circuits could not be manufactured. Why? Because the PCB designer, an electronic engineer, was not acquainted with the fabrication process. He had no idea about technological requirements necessary for electronic production. I know another designer who learned, finally, the importance of the thermal relief pad for heat restriction during reflow for a good soldering. His response? “Oh, was that what they were for? And to think I worked so much to remove them!”
Enough Blame to Go Around
The idea for this article began a few months ago when The PCB Design Magazine conducted a reader survey regarding the topic “Whose Fault is that Bad Board?” After some thought, I submitted my answers. After all, I must have some kind of input after over 25 years of PCB design. But still, whose fault is that bad board? OK, I know what you’re thinking: Don’t go there. We designers make mistakes too.
Orange Co. Designers Council Meeting Focuses on Embedded Passives
On July 19, the Orange County Chapter of the IPC Designer’s Council hosted a lunch-and-learn meeting in Tustin to discuss the benefits of embedded passives. Approximately 40 people were in attendance, which was lighter turnout than usual, most likely because of summer vacations. But the crowd was an enthusiastic one, as usual. The first speaker was Bruce Mahler of Ohmega Technologies, followed by Jin Hyun-Hwang of Dupont.
Romania’s PCB Design Students Compete at TIE 2017
During the last week in April, the 26th Interconnection Techniques in Electronics (TIE) show was held at the Gheorghe Asachi Technical University in Iasi, Romaina, a wonderful hill town not unlike Rome. The event, a convention for the Romanian electronic packaging community, included a series of actions designed to draw smart young students to the electronics industry, which is clearly growing. Participants had only four hours to create this PCB design, which was generated by a team of professionals from Continental Automotive Romania Timisoara.
PCB Design in the Age of IoT
From the early days of printed circuit boards, the electronics industry has made huge strides in board materials, copper printing methods, miniaturization, rigid-flex, ELIC, EDA, and much more. Many of the devices we use in our homes, our vehicles, and in our workplaces would not be possible without this continuous evolution of PCB design and technology. And yet in 2017, we are poised to shift from evolution to revolution, driven by the idea of the Internet of Things.
SnapEDA: Recruiting Top Engineering Talent in an Amazon World
You don’t have to love EDA to work at SnapEDA, but it helps. This startup, founded by Natasha Baker, is on its way to creating the world’s largest parts library for PCB designers. Baker leads a small team of young, fiercely talented engineers—the kind of employees that are attractive to companies like Google and Facebook. I asked Natasha to explain her hiring process, and how she ensures that each employee is the right fit for SnapEDA.
Steve Robinson Discusses APCT’s Tenfold Expansion
Steve Robinson, CEO of APCT, a PCB fabricator in Silicon Valley, has led the company to impressive growth since he acquired it nearly 10 years ago. I ran into Steve at DesignCon 2017, and we sat down to discuss the company’s remarkable transformation and his focus on working with PCB designers and engineers to create advanced, high-speed PCBs.
Sensible Design: Casting a Spotlight on Resin Applications
Over the last few columns, I’ve given readers pointers on virtually every aspect of potting and encapsulation resins, ranging from their formulations and special properties to their applications, benefits and limitations. It’s probably high time, therefore, to take a step back from the do's and don’ts and focus instead on how these resins are bringing very real benefits to practical electronic and electrical engineering applications. A good starting point is to look at the special requirements of an industry that is enjoying explosive growth: LED lighting.
'Flexdude' Tom Woznicki Celebrates Company’s 25th Anniversary
Twenty-five years ago, Tom “Flexdude” Woznicki got laid off. A lot of people did, back during the mini-recession that helped bring Bill Clinton into the White House. So, he launched his own flex circuit design bureau and never looked back. Since then, he’s designed flex circuitry for everything under the sun, including the Mars Rover; the flex circuits he designed are visible in many of the Rover photos. I ran into Tom at DesignCon 2017 and we discussed the benefits of flex circuits, the expansion of the flex market, and his company’s first quarter-century in operation.
Rigid-flex Design Tips and Best Practices
While the traditional “design-separately-then-assemble” approach minimized potential issues with the flex portions of the product, it also had several inherent disadvantages. These include the cost associated with the physical connectors; the space required for the physical connectors; the need to properly manage interconnects that have to transition between the separate rigid and flex PCBs (through the connectors); and, of course, the time and cost associated with assembly. The move to the current generation of rigid-flex technology mitigates these issues; however, they are replaced with a different set of challenges and concerns.
In Deep: The Art and Science of DFM with Gary Ferrari
When the topic of DFM techniques came up, I knew I had to talk with Gary Ferrari of FTG Corp. Gary has been involved with designing and manufacturing PCBs for decades, and he’s the past co-founder and executive director of the IPC Designers Council. I caught up with Gary between Thanksgiving and Christmas, and we conducted the following interview.
Flex and Rigid Sales and Marketing with Al Wasserzug
After decades in the PCB industry, Al Wasserzug of Cirexx International has seen marketing and sales trends come and go. I recently caught up with Al and interviewed him via email about the latest sales and marketing techniques, the value of traditional methods such as trade shows and conferences, and the particular characteristics of marketing flex circuits.
Resins: Five Essentials to Achieve the Right Cure
Last month, I looked at some of the critical things you need to consider before selecting your resin. Of course, when it comes to the choice and application of resins, there’s a lot of information to take in, and over the following months I hope to distill this and provide some useful tips and design advice that will help you in your quest for reliable circuit protection.
CAT’s David Wolf on Via Reliability Analysis
Conductor Analysis Technologies (CAT) has been analyzing test panels and coupon designs for over 20 years. CAT’s analysis provides valuable, quantitative data on PCB quality and reliability, which can help designers and manufacturers trace the source of defects and non-uniformities. Vice President of Technical Marketing David Wolf discusses some of the trends he’s seeing in via structures, and the common reliability and quality issues related to vias.
The Fundamentals of Improving PCB Thermal Design
Continental's automobile engineers have years of experience building critical parts and systems for automobiles. Making sure that automotive electronics are reliable, safe, and properly designed begins at the component level. Heat must be addressed early in the design process for these goals to be achieved. The most important thermal resistance for heat, outside the IC package, is the PCB.
Increasing Heat Dissipation in FPGAs
In recent years, the miniaturization and modularization of electronic products have led to the increased density of electronic components and the decrease of areas for effective heat dissipation. As a result, the thermal design of high-powered electronic components has become a major focus for electronics engineers. An effective solution for FPGA heat dissipation is critical. Thermal design of the PCB aims to decrease the temperature of both components and the board through suitable measures, so that the system is capable of working at a suitable temperature.
From the CAM Shop: Tight Tolerance Design Tips
After you finish your design, it winds up in the hands of people like Mark Thompson, the man who runs the CAM department at Prototron Circuits in Redmond, Washington. He sees CAD data firsthand, and often has to address errors and inconsistencies in PCB designs. For this issue, we asked Mark to discuss the today’s tight tolerances, some of the problems they can cause PCB designers, and what designers can do when dealing with shrinking features.
EDA Tools: Automation vs. Control
Stephen V. Chavez, CID+, is currently the lead PCB designer for the Electronic Systems Center division of UTC Aerospace Systems (UTAS). He's also a frequent speaker at the IPC APEX EXPO Design Forum. I caught up with Stephen and asked for his thoughts on the EDA tools of today, and whether he’d prefer to have more control vs. more automation.
Designers and Design Engineers: Two Sides of the Same Coin
Andy and Sue Critcher have been the lead designers at Total Board Solutions Limited, a UK-based design bureau, since its founding in 1998. I asked Andy to share his opinion about the friction between some PCB designers and their engineers, and what can be done to improve communications between these groups.
RTW IPC APEX EXPO: Geek-A-Palooza Coming to S. California May 12
Steve Williams sits down with Geek-A-Palooza founders Tara Dunn and Judy Warner to discuss their upcoming event in Irvine, California on May 12. The Geek-A-Palooza held in Minneapolis last year drew over 300 PCB designers, fabricators, assemblers and suppliers. Tara and Judy explain why this is not just another boring technical talk, and attendees will definitely enjoy themselves.
IPC APEX EXPO: Isola Introduces New Products, Increases R&D
Ed Kelley, VP of global technology, sits down with Guest Editor Dan Beaulieu at IPC APEX EXPO to discuss the company's plans for the future. The company is launching new low-loss laminates and increasing its R&D activities around the globe. He also explains why Isola often works with designers at OEMs.
Designers Notebook: Flexible and Rigid-Flex Circuit Design Principles, Part 4
All of the design rules for the glass reinforced-portion of the board (land pattern geometry for mounting surface mount devices, solder mask and the like) are now well-established. One unique facet of fabricating the rigid-flex product is how the flexible portion of the circuit is incorporated with the rigid portion of the circuit. As a general rule for multilayer PCB design, furnish a balanced structure by building up the circuit layers in pairs (4, 6, 8 and so on).
Enhancing Thermal Performance of CSP Integrated Circuits
In order to meet size and weight requirements, constraints of portable electronic designs often force PCB designers to reduce the size of components and PCB real estate area. To meet these demands, the use of CSP packages to shrink the PCB area needed is a common change in designs. As a result of the reduction of total PCB area, the available options to move heat and route high-power PCB traces is also reduced. Furthermore, the thermal performance cannot be matched when a QFN is compared to an equivalent CSP package.
The Shaughnessy Report: Doing My Part for Medical Electronics
One interesting aspect of having hernia surgery recently was the number of PCBs in the operating room. I’ve never seen so many electronic devices together in my life. I saw one Agilent monitor, and a bunch of others with names I couldn’t make out. It reminded me of the IT room in most companies. I guess they had to be set up to handle routine surgery like mine, and the not-so-routine operations as well. Medical electronics is doing fine, no doubt.
American Standard Circuits: Leading the Way in Medical Electronics
When it comes to innovative fabricators, American Standard Circuits is always at the front of the pack. Naturally, when Editor Andy Shaughnessy asked me to interview a fabricator about PCBs for the medical market, ASC was the one company that immediately came to mind. I spoke with CEO Anaya Vardya about fabricating medical PCBs, the medical electronics market, and the future of this fast-growing segment.
IPC Designers Council Viewpoint: Mike Creeden
When covering the IPC Designers Council, one quickly learns that it’s the volunteers who make the train run on time. San Diego PCB CEO Mike Creeden, CID+, is one such volunteer, and as a member of the Designers Council’s Executive Board, he was a must-have for this issue. I tracked him down and asked him to give us a rundown of his involvement with the DC, and to explain why designers might want to get involved with their local DC chapters.
The Shaughnessy Report: Are You Drowning in Data?
Data management was so much simpler during the days of Mylar and Bishop Graphics tape. Data was handwritten. All you had to do was keep track of your paperwork and you were golden. Now, you’re all much more productive, but you have data coming out of your ears; slowly but surely, incrementally, data has become much more complicated. How do designers and engineers wind up managing all of this data? With kluged-together processes and software tools, and the occasional handwritten notes.
DownStream Takes on Data Documentation Management
Most designers will tell you that, as much as they enjoy laying out boards, they dislike the final data documentation step, which often involves various formats, including handwritten notes. Enter DownStream Technologies, a company founded 14 years ago to address the challenges related to post-processing the design. Senior Product Marketing Manager Mark Gallant recently discussed the company’s efforts to take the pain out of data documentation, even as data becomes more complex.
Pulsonix Poised to Take More EDA Market Share
Publisher Barry Matties met with Bob Williams, managing director and co-owner of Pulsonix, and Sales and Marketing Manager Tyrone Stephens to discuss the challenges facing the EDA tool market, and how they’re establishing this company in the global design tool marketplace.
The Gerber Guide, Chapter 3: The PCB Profile
The profile defines a simple region in the 2D plane. The proper way to do this is to specify a closed contour: The inside of the contour is the PCB, and the outside is not. It is that simple. Note that such a simple region is solid, without holes. By definition then, a profile cannot have holes intentionally placed within it. These are superfluous and represent an unnecessary and complicated duplication given that drill holes are well defined in the drill/rout file. One can view cut-outs in a PCB as still part of the PCB, just as much as the drill holes are.
Arlon’s John Wright Discusses New High-Performance Materials
During productronica, European Editor Pete Starkey interviewed Engineering/Quality Manager John Wright of Arlon. They discussed Arlon’s new 85HP ceramic-filled polyimide, as well as a non-woven aramid material, suitable for space applications, that is a drop-in replacement for a similar material discontinued by a competitor in 2006.
Lightning Speed Laminates: Impact of Final Plated Finish on PCB Loss
A variety of plated finishes are used in the PCB industry. Depending on the circuit construction and other variables, the plated finish can cause an increase in PCB insertion loss. The plated finish used on the outer ground planes of a stripline circuit have minimal or no impact on insertion loss. However, microstrip or grounded coplanar waveguide circuits, which are common on the outer layers of multilayer high-frequency PCBs, can be impacted by the plated finish for increasing the insertion loss.
The Readers Speak: Tips on Accelerating your Design Cycle
This month, in addition to publishing feature articles by well-known experts in the field, we decided to collect feedback from the readers—PCB designers and engineers working in the trenches each day. We asked our readers to provide their favorite tips, tricks, and techniques for speeding up the PCB design cycle. Here are 10 tips for cutting your design time, courtesy of designers just like you.
The Shaughnessy Report: Squeezing Seconds Out of the Design Cycle
When you’re designing a board, time is always your enemy. That’s what we learned when we surveyed our readers recently. PCB designers said that time pressure was one of their least favorite parts of the job, and in some cases, they were ready to retire just to avoid design cycle challenges. I imagine that many of you near retirement, and that’s quite a few of you, feel the same way.
Top Gear: PADS Professional Road Test
In this column, Barry Olney test drives the newest version of the Mentor Graphics PADS Professional EDA tool. "Based on Xpedition technology, PADS Professional is a major improvement over the previous PADS suite of tools. utilizes xDX Designer as the front-end design entry tool. The latest routing technology is fast, smooth to drive, and hugs the corners well, with all the horsepower you need for the most demanding design."
Leo Lambert on EPTAC's Customized Training Plans
Andy Shaughnessy interviewed Leo Lambert, vice president and technical director of EPTAC, at SMTA International. Leo Lambert, vice president and technical director of EPTAC, explains how the New Hampshire-based company continues to provide customized training and IPC certification offerings, including its IPC Certified Interconnect Designer (CID) and CID+ classes.
The Gerber Guide, Chapter 2
Never mirror or flip layers! All layers must be viewed from the top of the PCB, which means that the text must be readable on the top layer and mirrored on the bottom layer. Alas, sometimes, in a mistaken attempt to be helpful, designers flip layers because they must anyway be mirrored on the photoplotter. This could be helpful in a world where the designer's files are used directly in fabrication, but these data layers are actually input for the CAM system.
Mentor Graphics Helps Bridge Gap Between PCB and RF
Recently, Publisher Barry Matties met with Per Viklund, the director of IC packaging and RF product lines at Mentor Graphics, and Alex Caravajal, business development manager with Mentor. They discussed the challenges facing PCB designers working with RF and microwave technology, and Mentor’s efforts to help reduce the RF design cycle time.
EMA Design Automation Connecting the Data with Arena PLM Software
During IPC APEX EXPO 2015, Guest Editor Kelly Dack sat down with Chris Banton, marketing manager for EMA Design Automation to discuss EMA’s recent partnership with PLM software provider Arena Solutions. Banton explains how the alliance benefits companies that use both platforms, and why more and more CAD tool users are also taking advantage of PLM.
Isola Launches Low-loss Laminate for 100 GB Ethernet Apps
I-Connect007 Technical Editor Pete Starkey and Isola’s Fred Hickman, senior director of high-speed digital products, spent time at IPC APEX EXPO 2015 talking about Isola’s recent launch of a low-loss, low-skew laminate prepreg. Hickman explains that the new material, Chronon, will be one of the enablers of 100GB Ethernet applications.
Cirexx Introduces Eclisp, An Alternative to Co-fired Ceramics
Al Wasserzug, SR Business Development Exec at Cirexx, talks about their new product, Eclisp. Developed in conjunction with Lockheed Martin, Eclisp is an alternative to co-fired ceramics and used to evacuate heat very efficiently with a low CTE. Wasserzug gave a paper on the new technology at IPC APEX EXPO.