-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueOpportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
Manufacturing Know-how
For this issue, we asked our expert contributors to share their thoughts on the absolute “must-know” aspects of fab, assembly and test that all designers should understand. In the end, we’re all in this together.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
All About Flex: Creating Via Holes in Flexible Laminates
July 28, 2016 | Dave Becker, All Flex Flexible Circuits LLCEstimated reading time: 4 minutes
Almost all double-sided and multilayer flexible circuits require through-holes or vias to enable an electrical connection between conductive layers. Creating a reliable plated via requires several critical steps. The first one is creating the through-hole.
Typical methods for creating through-holes in flexible laminates are:
- Numerically controlled drilling
- Laser drilling
- Hard tool punching
Numerically Controlled Drilling
Numerically controlled (NC) drilling is the most common method used in flexible circuit and printed circuit board manufacturing. Panels can be stacked several layers high and are sandwiched between entry and exit materials to ensure cleanly cut holes. Many NC drilling machines have multiple spindles, which allow multiple holes to be drilled simultaneously. Multiple spindle drilling combined with stacking make NC drilling a very efficient operation with a locational accuracy of about +0.001” from hole to hole. This technology has been around for decades but remains the workhorse process for making holes in panels of flexible and rigid circuit board material.
Drill bits can come in all shapes and sizes; most are carbide steel. The bit has angular sharp grooves that evacuate the material by a shredding action as the rotation of the drill cuts then pulls the material out of the way. The smaller the via diameter, the faster the drill should spin to achieve maximum cutting efficiency. Drill sizes may be as large as 0.250” for creating tooling locations and can go down to about 0.005” for the creation of electrical vias. While customers frequently ask “what is the smallest via you can drill?” practically speaking, an 0.008” diameter is close to the lower limit for efficient volume production.
While the side view of a drilled hole is smooth to the naked eye, it actually has spiraling microgrooves along the sidewall. Most substrates are composites with layers of copper, adhesive and polyimide. This complicates drilling as it must cut cleanly through several different types of materials. Drill bits can get hot and soften the adhesive, smearing it around the diameter of the hole. The bit temperature is a function of drill speed and the design of the bit. Optimal bit designs maximize material evacuation while minimizing temperature rise. Adhesive smear can create an insulation layer around the circumference of the drilled hole. This can prevent the copper plating from creating the layer-to-layer electrical connection. As a result, many double-sided and multilayer circuits are next processed through a plasma desmear operation to remove this dielectric layer.
Laser Drilling
In laser drilling, a highly focused beam of energy ablates or vaporizes the material. The laser beam consists of pulses of various intensities and wavelengths. Laminates comprised of multiple materials such as copper, polyimide and adhesive require specific process algorithms to address the material differences, since different materials ablate at different laser settings. Polyimide and adhesive are quickly removed while copper is much slower and requires increased energy. While NC drilling can handle a stack of multiple layers of material, laser drilling is only performed on a single substrate layer.
Virtually any size or shape opening can be created with laser drilling. The larger the hole, the more energy required and the higher the cost. Lasers can drill very small holes, but for flexible circuits, via sizes smaller than 0.002” may be difficult to plate due to the inherent limitations of the plating chemistries and processes. For high-density circuits with vias in the 0.002” to 0.006” range, laser drilling is often preferred over NC drilling. NC drilling would most likely be preferred for larger vias because of the higher throughput rate.
Laser drilling can be highly controlled in the X, Y and Z directions as well as be tuned to selectively ablate specific materials. This capability makes the technology useful for multilayer fabrication where blind and buried vias are required. It is also used to create dual access openings on top and bottom sides of a single-sided circuit by selectively removing polyimide and adhesive. Even with a finely tuned laser output, there is often some carbon debris remaining in the hole requiring removal. This is usually accomplished with a plasma etch process. Alternative chemical cleaning processes are also employed.
Punching
Punching vias is usually performed using a male-female die set. The upper section of the tool is a punch and the lower part is the die. Laminate is placed between the upper and lower plate. The top punch is pushed into the material and a sheering action creates the hole. The slug created by the punch is pushed through the lower die plate.
Punching is the least frequently used process for flexible circuit fabrication, especially for low volume or quick turn parts. It does find favor with ultra-high volume, lower density circuits and lends itself well to continuous reel-to-reel circuit fabrication. Die sets can be quite expensive depending on the number and size of holes in the pattern. A die set can be built to accommodate a variety of shapes and sizes but this process has limitations for creating vias in high density circuit applications. For most manufacturers, 0.015” to 0.020” diameter punches are the practical limitation for via size with a punch tool.
Of the three methods, punching puts the highest level of mechanical stress on the substrate. At a microscopic level, a punched hole will look deformed when compared to NC or laser drilling. A dull punch can result in the substrate layers pulling apart, or the adhesive layer smearing over the copper part of the sidewall. This can cause problems at plating and result in a poorly metalized through-hole. An undetected broken punch is also an obvious problem.
Hard tooling, NC drilling, and laser drilling all have advantages and disadvantages in flexible circuit processing. The preferred method depends on circuit density, production volume and laminate configuration. From a plating standpoint, there are no inherent advantages among the three alternatives.
Dave Becker is vice president of sales and marketing at All Flex Flexible Circuits LLC.
Suggested Items
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?
AT&S Shines with Purest Copper on World Recycling Day
03/18/2024 | AT&SThe Styrian microelectronics specialist AT&S is taking World Recycling Day as an opportunity to review the progress that has been made in recent months at its sites around the world in terms of the efficient use of resources:
Matrix to Exhibit at IPC APEX EXPO 2024 in Anaheim, CA
03/05/2024 | MatrixMatrix will be exhibiting at IPC APEX EXPO 2024, to be held on April 9-12, 2024, at the Anaheim Convention Center, Anaheim, CA.
The Chemical Connection: Getting to Know Your Vendor
02/16/2024 | Don Ball -- Column: The Chemical ConnectionAfter working for a capital equipment supplier for almost 50 years, I’ve found that the most important part of getting to know your vendor is good communication among all parties. While contact between fabricators of a constantly changing product line and the designers of those products may occur daily or weekly, conversations between you and your equipment supplier may be years apart. That lengthy gap often means that previous contacts may have been promoted, retired, or moved on to other opportunities. You may have also migrated to a new supplier with whom you have little or no history. In either case, you will be interacting with someone you are unfamiliar with (as they are with you). Therefore, it is essential for both sides to communicate clearly so expectations will align.
EIPC Winter Conference 2024, Day 2: A Closer Look at Global Trends
02/14/2024 | Pete Starkey, I-Connect007The opening session of the second day’s conference proceedings focused on global PCB trends and was introduced and moderated by Dr. Michele Stampanoni, vice president of strategic sales and business development at Cicor Group in Switzerland. He opened the session with Dr. Hayao Nakahara’s knowledgeable and enlightening video presentation on the IC substrates industry.