Designs on Flex: Underwriters Laboratory and Flexible Printed Circuits
November 12, 2015 | Mike Morando, PFC Flexible CircuitsEstimated reading time: 1 minute
Underwriters Laboratory is a worldwide safety consulting and certification company headquartered in Northbrook, Illinois. UL certifies, validates, tests, inspects, audits, and advises on safety of electrical and electronic products.
I am sure you have seen the UL logo on many of your electrical and electronic products at home. Electronic equipment, in many cases, requires a UL certification. In turn, the components that make up the electronic or electrical system must be certified.
What Does UL test?
The test process for UL varies based on what is being certified, but in essence, the tests consist of determining how flammable a product is and the functionality of the circuit. In most cases, UL will perform flammability on the consumer product to insure its safety.
For UL 796F standard,
There are two categories of the safety test: flammability and function.
- Adhesion
- Bending / fatigue
- Current / voltage limit
UL 94 Standard
These requirements cover tests for flammability of plastic materials used for parts in devices and appliances. There are three grades of flammability rating:
1)Vertical Burning Test: V-0, V-1, or V-2
2) Thin Material Vertical Burning Test: VTM-0, VTM-1, or VTM-2
3) Horizontal Burning Test: HB
UL Testing of Flex Materials
To obtain UL certification for a flex circuit is a little different. UL does not require each flex circuit to be tested and certified, but, rather the materials that make the circuit- (specific stack up of polyimide, copper, FR-4 and adhesive).
To get approval from UL, a flex circuit manufacturer provides samples of a specific construction for flammability and flexibility testing. UL will test and approve that specific construction. Once the construction is approved, the flex manufacturer can use that specific construction on other circuits as a UL-approved construction.
Process
From a high level, here are the procedures to get specific flex materials certified for flammability from UL.
- Flex vendor submits request to UL have a flammability test
- UL evaluates and creates a test plan,, procedures and processes. Test plan includes flammability test
- Flex vendor manufactures test samples (coupons) and provides all required paperwork
Testing and certification takes 8-10 weeks.
Suggested Items
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?