Karel Tavernier: The Gerber Guide


Reading time ( words)

It is clearly possible to fabricate PCBs from the fabrication data sets currently being used—it's being done innumerable times every day all over the globe. But is it being done in an efficient, reliable, automated and standardized manner? At this moment in time, the honest answer is no, because there is plenty of room for improvement in the way in which PCB fabrication data is currently transferred from design to fabrication.

This is not about the format, which for over 90% of the world's PCB production is Gerber: There are very rarely problems with Gerber files themselves. They allow images to be transferred without a hitch. In fact, the Gerber format is part of the solution, given that it is the most reliable option in this field. The problems actually lie in which images are transferred, how the format is used and—more often—in how it is not used.

In this monthly column, Karel Tavernier explains in detail how to use the newly revised Gerber data format to communicate with your fabrication partners clearly and simply, using an unequivocal yet versatile language that enables you and them to get the very best out of your design data. Each month we will look at a different aspect of the design-to-fabrication data transfer process.

This column has been excerpted from the guide, PCB Fabrication Data: Design-to-Fabrication Data Transfer.

 

Chapter 1: How PCB Design Data is used by the Fabricator

In this first article of the series, we’ll be looking at what happens to the designer's data once it reaches the fabricator. This is not just a nice add-on, because for designers to construct truly valid PCB data sets, they must have a clear understanding of how their data is used. This, more than anything else, clarifies how it should be prepared.

We will not look at how to design PCBs for easy fabrication, which is completely outside the remit of the developer of the Gerber format and a matter for the PCB fabricators themselves.

What does a PCB fabricator do with CAD fabrication data?

PCBs are typically fabricated in about 22 steps, many of which are digitally controlled and require dedicated data modules called production tools.

Some designers believe that their PCB fabrication data will drive the fabricator's production machines directly; that the Gerber files will be used directly on the PCB fabricator's photoplotter; that Excellon drill files will go straight onto the fabricator's drilling machines; and that IPC-D-356A netlist will go right into electrical test machines.

Not so. Fabricators never use the Gerber or Excellon files directly on their equipment.

There are many reasons for this, the simplest of which is panelization. Even though the designer's data describes a single PCB or maybe an array, the job is never manufactured as such. It is always put on a production panel, which will typically have multiple jobs on it, as well as a border for plating, test coupons, etc. 

To read this entire article, which appeared in the July 2015 issue of The PCB Design Magazine, click here.

Share




Suggested Items

I-Connect007 Editor’s Choice: Five Must-Reads for the Week

01/20/2023 | Andy Shaughnessy, Design007 Magazine
We’re in the middle of show season, and it certainly “shows.” Thank you very much. I’m here all week. Don’t forget to tip your wait staff. This week, we published a variety of articles, columns, and news items, and much of it centered on trade shows. Technical Editor Dan Feinberg brings us a report from CES 2023. IPC announced the winners of the Best Technical Paper awards for IPC APEX EXPO 2023. And we have an interview with Altium’s Rea Callender about the company’s educational efforts at APEX and around the globe.

Altium Focuses on Design Education

01/16/2023 | I-Connect007 Editorial Team
Altium keeps its eyes on the designers of the future. The company has been working with colleges and universities for years, providing free seats of Altium Designer for the next generation of PCB designers and design engineers. At IPC APEX EXPO 2023, Altium will be providing software for the finalists in the IPC Design Competition just as it did last year. They offer a variety of other educational programs as well, including Upverter classes and a design competition that aims to address environmental change. Here, Rea Callender, Altium’s VP of education, discusses its educational programs and plans for the week of the show.

The Battle of the Boards

01/12/2023 | Patrick Crawford, IPC
Last year, IPC held its first-ever design competition at IPC APEX EXPO in San Diego. PCB designers from around the world competed in a series of heats during the months before the show, culminating in a showdown on the show floor between the top three finalists. Rafal Przeslawski, now with AMD, took home the top prize last year. This year, the competition is back for its sophomore year. I asked Patrick Crawford, manager of design standards and related programs for IPC, to “layout” the details on the design contest, including lessons learned in 2022 and what’s new for the 2023 competition.



Copyright © 2023 I-Connect007 | IPC Publishing Group Inc. All rights reserved.