HDI Design Education: Is Anyone Interested?


Reading time ( words)

I first became aware of high-density interconnection (HDI) design methodology in 1997 when a co-worker of mine came back from a training class that was taught by Happy Holden. “Little Dave” (since our department had two employees named David W.) came back excited to try this new design knowledge on a multilayer board stackup that only used blind and buried vias, with no through-hole vias. His excitement and dedication paid off, as he completed the design with an autorouter exactly as he planned. Through Dave’s success, our department then started to create other designs using HDI stackups that were taught in Happy’s class and our autorouter tool.

I did a few complex designs that fit into the IPC Type III category. One of the more complex designs I attempted could only autoroute up to 98% completion after trying many setup files (with great assistance from “Big Dave”) and our most powerful computer available within our group. I finished the design manually, and the board was fabricated and worked as designed.

About six months later, when we upgraded our department’s autorouter computer, I restored the design from archive, and re-ran the last autorouter configuration file on that 98% completed design. This time, the design was now 100% completely autorouted, and took about a third less time than on the previous “most powerful” computer. This one little re-investigation became the catalyst for my full immersion into HDI design research, reviewing the existing designs and now trying newer autorouting approaches with a variety of more challenging stackups, via spans, and via sizes. Each new redesign attempt created more curiosity to push autorouters and stackup methodologies to their absolute limits.

Over the next few years, any article written on HDI that crossed my path became assimilated into my mental database. I met Mike Fitts lecturing on HDI at a design conference, and I asked him to clarify my repository of HDI re-design questions. When Mike and I met at another design conference, he introduced me to the very person who inspired Little Dave: Happy Holden.

Read the full column here.


Editor's Note: This column originally appeared in the May 2014 issue of The PCB Design Magazine.

I first became aware of high-density interconnection (HDI) design methodology in 1997 when a co-worker of mine came back from a training class that was taught by Happy Holden. “Little Dave” (since our department had two employees named David W.) came back excited to try this new design knowledge on a multilayer board stackup that only used blind and buried vias, with no through-hole vias. His excitement and dedication paid off, as he completed the design with an autorouter exactly as he planned. Through Dave’s success, our department then started to create other designs using HDI stackups that were taught in Happy’s class and our autorouter tool.

I did a few complex designs that fit into the IPC Type III category. One of the more complex designs I attempted could only autoroute up to 98% completion after trying many setup files (with great assistance from “Big Dave”) and our most powerful computer available within our group. I finished the design manually, and the board was fabricated and worked as designed.

About six months later, when we upgraded our department’s autorouter computer, I restored the design from archive, and re-ran the last autorouter configuration file on that 98% completed design. This time, the design was now 100% completely autorouted, and took about a third less time than on the previous “most powerful” computer. This one little re-investigation became the catalyst for my full immersion into HDI design research, reviewing the existing designs and now trying newer autorouting approaches with a variety of more challenging stackups, via spans, and via sizes. Each new redesign attempt created more curiosity to push autorouters and stackup methodologies to their absolute limits.

Over the next few years, any article written on HDI that crossed my path became assimilated into my mental database. I met Mike Fitts lecturing on HDI at a design conference, and I asked him to clarify my repository of HDI re-design questions. When Mike and I met at another design conference, he introduced me to the very person who inspired Little Dave: Happy Holden.

Read the full column here.


Editor's Note: This column originally appeared in the May 2014 issue of The PCB Design Magazine.

Share




Suggested Items

Altimade Puts Designers and Manufacturers Together

06/24/2022 | Andy Shaughnessy, Design007 Magazine
Despite all of the talk about the need for communication between designers and manufacturers, many PCB designers still do not talk with their manufacturers for a variety of reasons. Altium and MacroFab aim to change this dynamic. In this interview, Ted Pawela, chief ecosystem officer of Altium and head of Altium’s Nexar Business Unit, and MacroFab CEO Misha Govshteyn, discuss the new Altimade manufacturing service that Altium is introducing in partnership with MacroFab. Ted and Misha provide an overview of the Altimade process, how it links designers to fabricators, assembly providers, and component distributors, and they explain how it could pave the way for true design with manufacturing, or DWM.

The Survey Said: Why Don’t You Know Your Fabricator?

06/23/2022 | I-Connect007 Editorial Team
When we want to find out what challenges our readers are facing, we just ask. And they don’t mind sharing—the good, the bad, and the ugly. In a recent survey, we asked our PCB designer readers, “Why don’t you know who is going to manufacture your boards?” Here are some of more interesting replies we received, edited slightly for clarity. Do you see yourself in these replies?

Producing Diverse Designs in Concert With Manufacturing

06/16/2022 | Scott Miller, FreedomCAD Services
There is a new acronym bubbling up in the design world: DWM, which stands for “design with manufacturing.” Why is this different than design for manufacturing, or DFM? With DWM, the emphasis is on integration between the design team and the manufacturers during the design process. DWM is much more than that. We are tasked with producing designs that meet various technical requirements, yet are cost-effective and manufacturable. We provide this service to hundreds of customers who have varying degrees of processes, tools, and manufacturing partners. Given this diversity, we have recognized the importance of designing with manufacturing to achieve the product development goals of manufacturability and technical excellence.



Copyright © 2022 I-Connect007. All rights reserved.