ICT Seminar 2023 Review: Energy, Thermals, and Assistive Technology

Reading time ( words)

Widely believed to be the traditional Centre of England, Meriden was a popular venue for a gathering of the UK printed circuit community this month. They braved the forecast of heavy snow for the Institute of Circuit Technology’s annual general meeting to learn about current developments and challenges in a thought-provoking technical seminar and to network with industry peers and contemporaries. Thankfully, the forecasted heavy snowfall did not reach Meriden until after the event; we only had a few flurries, although the weather caused considerable disruption elsewhere in the country.

ICT_Seminar_Rex_Rozario.jpgAfter the formal business of the annual general meeting had been efficiently managed and conducted by ICT Chair Emma Hudson, the early highlight of the evening session was the award of Honorary Fellowship to Rex Rozario OBE. He is credited with being part of the team that developed the first circuit board in England in the 1950s. 

The State of Energy
Technical director Bill Wilkie introduced and moderated the seminar program. Alun Morgan, president of EIPC, was the first speaker and brought his views on energy, both in general and in the real-world situation. 

The increasing availability of energy has transformed the course of humanity, he said, and the quantity consumed and produced has inevitably continued to increase. Fossil fuels have been supplemented with new energy sources: hydropower, nuclear and more recently with renewable technologies. Although decarbonisation is progressing slowly, it is essential that fossil fuels be displaced in the energy mix at a much faster rate.

His charts of global energy consumption and energy production by fuel type illustrated the wide gap that exist between:

  • Groups of principal sources: oil, coal, and gas
  • Groups of alternatives: biofuel, solar, wind, nuclear, hydropower, etc.

The challenge is in determining how to bridge that gap if the use of oil, coal, and gas are progressively discontinued. Neither solar nor hydro alone will be sufficient, and Morgan highlighted the example of nuclear power as adopted by France, where it has been calculated that the release of over 30 billion tons of CO2 emissions has been avoided, and the principal remaining source of air pollution is motor vehicles. The current area of interest is in small and simpler units for generating electricity and process heat from nuclear power, driven by the need to reduce capital costs and to avoid large grid systems. Morgan remarked that numerous technologies are involved; he mentioned the development of Generation 4 nuclear reactors based on Uranium 238, of which there is an abundant supply, and that is expected to be in service commercially around 2030. 


Morgan then focused on the PCB industry, reviewing world trends and concluding with Europe’s position. Whereas world PCB production has grown from $33.1 billion in 2000 to $60.8 billion in 2019, Europe’s share has reduced from $5.4 billion to $1.9 billion during the same period. But although the number of manufacturers has shrunk from 550 to 173, revenues have remained relatively stable since 2010. The European PCB industry is losing ground due to raw materials and equipment being increasingly difficult to source in Europe, reduced investment capital compared with other regions, and reduced availability of technical resources and workforce. The relative stability of the industry is closely related to its areas of specialisation: strong defence and aeronautics sectors, strong medical sector, and other specialised areas. Presently, the top 30 companies made 70% of the volume in Europe. But the industry was heavily dependent on its supply chain and needed to maintain its critical mass to secure supply continuity. 

Returning to Morgan’s primary topic, the unique competitive disadvantage Europe suffers relative to its competitors is the cost of energy. In 2021, even before Russia invaded Ukraine, the average price of electricity in U.S. dollars per kilowatt hour was $0.323 in Germany compared with $0.109 in the U.S. and $0.084 in China. 

In seeking government support, current employment numbers in the PCB industry are not large enough to have meaningful political significance, but defence and security considerations certainly are—a stable European supply base is considered essential—and it is from this perspective that government is being approached.

Andy_Colbey.jpgA Focus on Assistive Device Technology
Coventry University continues to collaborate in a wide range of international research and innovation programs, and has acted as coordinator for the Maturolife assistive technology project aimed at providing older people with security to enable them to live independently. Existing alarms and tracking devices designed to alert carers to falls or a person’s location are often unsightly, stigmatising the user and resulting in high abandonment rates. The interdisciplinary Maturolife research team includes creative artists and fashion designers as well as specialists in nanotechnology, electrochemistry, and materials science, to integrate electronics and sensors into fabrics and textiles while achieving a balance between aesthetics and functionality. Professor Andy Cobley reported the development of a selective metallisation technique for depositing electroless copper to fully encapsulate individual fibres in textile materials. The outcome is a fabric with normal feel and drape, selectively conductive but with no metal wires.

A key component of the process is an ink-jettable copper-silver core shell catalyst. This is an alternative to palladium which, although an excellent catalyst, was very expensive and classified as a “critical raw material.” Pure copper nanoparticle colloids are not stable and tend to aggregate over time. Using polyacrylic acid as a shell-ligand produces a stable colloid which enables a uniform electroless copper deposit, but the long-term stability of the ink needs improvement. Adding silver nitrate to a copper nanoparticle/polyacrylic acid dispersion results in an exchange reaction, creating a silver-core shell colloid. This is formulated into an ink-jet printable catalyst, and the silver shell significantly increased the lifetime of the ink. Printed onto a polyester fabric, this ink enables selective metallisation with electroless copper and increasing the number of print cycles increases the copper mass gain. It has been observed that the resistance of the copper deposit decreases with increasing print cycles, there is some difference between warp and weft directions, and resistance increases after each washing cycle.

Professor Cobley showed examples of Maturolife prototypes incorporated into assistive footwear, designed to help in the understanding of gait and balance.


Suggested Items

Paige Fiet: Forging a New Path

03/15/2023 | Patty Goldman, I-Connect007
As a young industry professional, Paige Fiet, a process engineer at TTM Logan, sees mentorship as a formative component of her success in IPC. Alongside the support and guidance of her mentors, Paige has distinguished herself as an emerging leader who brings a fresh perspective to the many topics currently of interest to the industry.

IPC APEX EXPO 2023 Special Session: Advanced Packaging

03/13/2023 | Pete Starkey, I-Connect007
The IPC APEX EXPO Special Session on Advanced Packaging this year attracted enormous interest, with Conference Room 2 at capacity long before the session began. Even with lots of extra seats squeezed around the edges, the session was standing room only for the just-in-time arrivals. IPC Chief Technology Officer Matt Kelly opened proceedings by introducing a distinguished panel of experts: Jan Vardaman, president and founder of TechSearch International; Sam Salama, CEO of Hyperion Technology; Matt Neely, director of process engineering at TTM Technologies; and Jim Fuller, VP of engineering technology at Sanmina.

Real Time with... IPC APEX EXPO 2023: Importance of Additive Manufacturing

03/09/2023 | Real Time with...IPC APEX EXPO
Nolan Johnson meets with Luca Gautero, product manager at SUSS MicroTec, developer of the SUSS JETx solder mask printer. Luca discusses why additive manufacturing is important and the role SUSS plays in this area.

Copyright © 2023 I-Connect007 | IPC Publishing Group Inc. All rights reserved.