Webinar Review: Thermal Integrity of High-Performance PCB Design


Reading time ( words)

Electrical and mechanical engineers may be working on the same product development teams, but they speak different languages, and they have completely different objectives. As a result, these folks almost never use the same software tools.  

But Cadence’s new Celsius Thermal Solver is an exception to the rule. In a new CadenceTECHTALK webinar, “How Static and Dynamic IR Drop Analysis Can Help PCB Designs and Challenges,” product manager Melika Roshandell and SerDes SI/PI engineer Karthik Mahesh Rao explain how the EE and ME can both use the Celsius Thermal Solver to achieve their disparate objectives—at the chip and package/board levels. 

Melika discusses the solver’s capabilities on the PCB and packaging side, which are accessible during pre-layout stages of the design cycle. Built on FEA and CFD engines, the solver can identify Joule heating on boards and packages, and help determine copper density, component spacing, and proper placement and size of thermal vias. She compares the results of the solver’s dynamic IR drop analysis with DC analysis, which only works with uniform temperature. Melika also points out the differences between typical thermal simulation and the solver’s electrothermal co-simulation. 

Karthik then takes over, demonstrating electrothermal co-simulation by importing an entire CAD file into the Celsius environment. He utilizes PowerTree technology to organize heat sources and heat sinks—definitions, model names, target impedance constraints, etc. He places probes at different points on the PCB and tracks the transient results of components across various points of time. He shows how to trace power loss across each layer across time, and changes in power distribution as well. The 3D modeling capability depicts any potential hot spots on the board. 

To illustrate how this PCB would operate in the real world, Karthik switches to the CFD analysis environment and places the design inside an enclosure. He adds a heat sink to one of the thermally problematic packages, and a cooling fan on the side of the enclosure, then traces the cooling flow across the component and board. Karthik closed with examples of the more comprehensive results attained through transient electrothermal co-simulation vs. traditional steady state analysis. 

The Celsius Thermal Solver continues the “shift left” of signal integrity horsepower into the front end of the design cycle, and it offers functionality that will appeal to electrical and mechanical engineers. Maybe EEs and MEs will eventually speak the same language after all. 

Melika and Karthik pack quite a bit into this half-hour webinar. If you’re dealing with thermal challenges in your high-speed PCB designs, you’ll want to check out the CadenceTECHTALK, “How Static and Dynamic IR Drop Analysis Can Help PCB Designs and Challenges.” 

Watch now! 

Related content:

Shift Left: Moving Multiphysics into the Mainstream by Sherry Hess

Successful Thermal Management of 3D-ICs: Accurate, Fast, Efficient, and Scalable with Celsius by Melika Roshandell

The System Designer's Guide to... System Analysis: Electromagnetic Interference and Thermal Analysis of Electronic Systems by Brad Griffin

The Cadence System Design Solutions Guide

“Cadence Provides ‘Clarity’ in Design Tool” Interview with Brad Griffin, Design007 Magazine, (July 2022)

Share




Suggested Items

Pulsonix Collision Avoidance to Bring Mechanical Capabilities Into ECAD

05/19/2022 | I-Connect007 Editorial Team
The I-Connect Editorial Team recently spoke with Bob Williams, managing director of Pulsonix. He discussed some of the new features in the upcoming version of the Pulsonix PCB design tool, Version 12, including collision avoidance and other 3D options that allow certain MCAD functions within the ECAD environment.

A Textbook Look: Signal Integrity and Impedance

05/18/2022 | Pete Starkey, I-Connect007
Believing that I knew a bit about signal integrity and controlled impedance, I was pleased to take the opportunity to connect with an educational webinar that I hoped would extend my knowledge. In the event I was surprised at how little I actually knew, and the webinar was an excellent learning opportunity. The webinar was introduced and expertly moderated by Anna Brockman of Phoenix Contact in Germany.

Designing in a Vacuum Q&A: Carl Schattke

05/11/2022 | Andy Shaughnessy, Design007 Magazine
Not long ago, I caught up with Carl Schattke, CEO of PCB Product Development LLC and a longtime PCB designer, for his thoughts on “designing in a vacuum.” As Carl points out, if you follow PCB design best practices, knowing the identity of your fabricator is not a “must-have.” He also offers some communication tips for discovering the information you do need, including one old-fashioned technique—just asking for it.



Copyright © 2022 I-Connect007. All rights reserved.