Rogers to Highlight High-speed Laminates and Next-Gen Thin Materials at DesignCon 2020


Reading time ( words)

Rogers Corporation will exhibit at DesignCon in Santa Clara, CA (at booth #421) highlighting some of its high-performance circuit materials used in multilayer structures which include a family of thin laminates, bonding materials, and sheeted copper foil options.

DesignCon is a premiere event for electronic design engineers working on circuit and system levels. Held at the Santa Clara Convention Center, the event takes place January 29-30. 

Visitors to Rogers’ booth will learn more about:

XtremeSpeed™ RO1200™ Laminates

XtremeSpeed RO1200 high speed, extremely low loss laminates, with a low dielectric constant of 3.05, and a maximum dissipation factor of 0.0017 @10 GHz, provide outstanding signal integrity, reduced signal skew, and reduced cross-talk. Combined with superior thermal/mechanical performance, low CTE, and a halogen free UL 94 V-0 rating, these laminates are well suited for the most demanding high layer count applications.

As channel speeds rise to 112Gbps and beyond, hardware designers need high performance circuit materials with superior electrical properties for applications like Network Infrastructure, High Performance Computing, and Test & Measurement. XtremeSpeed RO1200 circuit materials are engineered to meet the unique electrical and thermal/mechanical demands of high speed designs and enable system designers the flexibility to design leading edge systems that maximize data throughput and minimize latency in performance demanding applications.

RO4000® Products for Multilayer Structures

Next generation products designed to meet the existing and emerging needs of advanced millimeter wave multilayer designs. RO4835T™ laminates, offered in a 2.5 mil, 3 mil and 4 mil core thickness, are 3.3 Dk, low loss, spread glass reinforced, ceramic filled thermoset materials designed for inner-layer use in multilayer board designs, and they complement RO4835™ laminates when thinner cores are needed. 

RO4450T™ 3.2-3.3 Dk, low-loss, spread glass reinforced, ceramic filled bonding materials were designed to complement RO4835T laminates and the existing RO4000 laminate family, and come in 2.5, 3, 3.5, 4, 4.5, 5 or 6 mil thicknesses. 

RO4835T laminates and RO4450T bonding materials exhibit excellent Dk control for repeatable electrical performance, a low z-axis expansion for plated through-hole reliability, and are compatible with standard epoxy/glass (FR-4) processes. These materials are an excellent choice for multilayer designs requiring sequential laminations, as fully cured RO4000 products are capable of withstanding multiple lamination cycles. RO4835T laminates and RO4450T bondplys have the UL 94 V-0 flame retardant rating, and are compatible with lead-free processes.

Lastly, CU4000™ and CU4000 LoPro® Foils are sheeted foil options for designers looking for foil lamination builds, and provide good outer layer adhesion when used with RO4000 products.

RO3003G2™ high frequency laminates build on Rogers’ industry-leading RO3003™ platform to provide designers with improved insertion loss and reduced Dk variation. The combination of Rogers’ optimized resin and filler content along with the introduction of very low-profile ED copper translates to Dk of 3.00 @ 10 GHz (clamped stripline method) and 3.07 @ 77 GHz (microstrip differential phase length method).  RO3003G2 laminates also show very low insertion loss of 1.3dB/inch for 5 mil laminates as measured by the microstrip differential phase length method. 

CLTE-MW™ laminates are reinforced with spread glass, which along with a high filler loading help minimize the high frequency glass weave effects on electromagnetic wave propagation. The woven glass reinforcement also provides excellent dimensional stability. Other key features of the laminate include low z-axis CTE (30ppm/°C) for excellent plated through hole reliability, a low loss tangent of 0.0015 at 10 GHz to enable low loss designs, and low moisture absorption of 0.03% to ensure stable performance in a range of operating environments. Thermal conductivity of 0.42 W/(m.K) enables heat dissipation in aggressive designs along with a high dielectric strength of 630 V/mil to ensure good z-axis insulation between conductor layers. The UL 94 V-0 flammability rating enables the use of CLTE-MW laminates in commercial applications including Amplifiers, Antennas, Baluns, Couplers and Filters.

Technical Conference Presentation

On the technical conference side, Al Horn, Rogers Research Fellow, will participate in a panel discussion “Next Generation Materials for High Speed Digital Design” on Jan. 29, from 3:45 – 5:00 p.m. 

About Rogers Corporation
Rogers Corporation (NYSE:ROG) is a global leader in engineered materials to power, protect, and connect our world. With more than 180 years of materials science experience, Rogers delivers high-performance solutions that enable clean energy, internet connectivity, and safety and protection applications, as well as other technologies where reliability is critical. Rogers delivers Power Electronics Solutions for energy-efficient motor drives, e-Mobility and renewable energy; Elastomeric Material Solutions for sealing, vibration management and impact protection in mobile devices, transportation interiors, industrial equipment and performance apparel; and Advanced Connectivity Solutions for wireless infrastructure, automotive safety and radar systems. Headquartered in Arizona (USA), Rogers operates manufacturing facilities in the United States, China, Germany, Belgium, Hungary, and South Korea, with joint ventures and sales offices worldwide. For more information, visit www.rogerscorp.com.

Share

Print


Suggested Items

EIPC Technical Snapshot: Supply Chain and Material Price Pressures

04/26/2021 | Pete Starkey, I-Connect007
EIPC’s seventh Technical Snapshot webinar on April 14 was timely and appropriate. In the context of current supply chain issues and material price pressures facing the PCB industry, particularly in Europe, the EIPC team brought together an outstanding group of experts—each a leading authority in his field—to analyse and comment upon the areas of concern and to respond to questions raised by a capacity audience. As Alun Morgan said, “If you don’t use the European supply chain, you won’t have it anymore!”

Time, Space, Structure, and Model Analysis of CCL Price Increase

04/19/2021 | Hu Yang, Zhongtai Securities Research Center
According to the CCL Association, copper foil accounts for the largest proportion of raw materials (traditional CCL uses epoxy resin, glass fiber cloth and copper as raw materials). Copper foil in thin plate accounts for about 30% of the overall cost; in thick plate copper accounts for 50%. In CCL production, using Shengyi Technology and Chaohua Technology as examples, the cost of raw materials accounts for about 88% of the total cost, with labor accounting for about 4%. Other costs such as equipment depreciation account for about 8%.

Top Five Takeaways from IPC APEX EXPO 2021

04/15/2021 | Chris Mitchell, IPC VP, Global Government Relations
IPC APEX EXPO 2021, which went all virtual this year, exemplified how the electronics industry has responded to the COVID-19 global pandemic: with resiliency, agility, and an unwavering commitment to build electronics better. APEX EXPO featured great content and robust discussions on topics of critical importance to the global electronics industry. From my vantage point leading IPC’s government relations programs, here are my top five takeaways from this year’s event.



Copyright © 2021 I-Connect007. All rights reserved.