A Handy Compilation of Our Top 10 DFM Articles


Reading time ( words)

When we started working on this issue, I searched through our files and found that we’ve published some great DFM articles over the past year or so. While topics like signal integrity tend to get most of the limelight, in the end it all comes down to solid DFM practices. So, without further ado, we present this compilation of our Top 10 DFM articles and columns, culled from the pages of The PCB Design Magazine and The PCB Magazine. Enjoy.

The Top 10 Ways Designers Can Increase Profits

So, can you truly increase profitability through PCB design practices? Yes, you can. And it starts with a philosophy that embraces DFM techniques. Then you must be ready for the initial release to a fabricator by ensuring that you are communicating all of your specifications and needs clearly to the fabrication house so that you get an accurate quote. By Mark Thompson.

Beyond Design: The Need for Speed—Strategies for Design Efficiency

Years of experience with one EDA tool obviously develops efficiency, whether the tool be high-end feature-packed or basic entry-level. However, there comes a time, with the fast development pace of technology, that one should really consider a change for the better to incorporate the latest methodologies. This month, I will look at productivity issues that impede the PCB design process. By Barry Olney.

Brooks' Bits: How Many Vias Does It Take To…?

Sounds like the opening words of a bad joke. Well, here’s the answer, and it’s no joke: One! That’s right. No matter how much current you are putting down the trace, all you need is a single via. And a small one, at that. OK, that last statement might not be true in every single case. But it is true in a LOT more cases than you think. I will explain why in this column. By Douglas G. Brooks.

Mark Thompson: It’s All about Communication

During DesignCon, we talked with columnist Mark Thompson about why communication is paramount when designing and prototyping boards. Thompson also explained how designers can avoid making common mistakes that can set back an entire project. By Barry Matties and Andy Shaughnessy.

Trouble in Your Tank: Building Reliability into the PCB, Part 2

Many engineers have been in this situation: Process audits are completed. Personnel who have direct influence are properly trained. Analytical controls are in place. Great! Yet there are boards that are not meeting specification (IPC 6010 Series, IPC 600, IPC 610). And now the team has to deal with the rejects and provide corrective actions. By Michael Carano.

To read this entire article, which appeared in the January 2017 issue of The PCB Design Magazine, click here.

 

Share


Suggested Items

Dave Wiens Discusses Multi-board Design Techniques

07/09/2018 | Andy Shaughnessy, I-Connect007
For our multi-board design issue, I interviewed Dave Wiens, product marketing manager for Mentor, a Siemens business. We discussed how the multi-board design technique differs from laying out single boards, along with the planning, simulation and analysis processes required to design multi-board systems.

Paving the Way for 400Gb Ethernet and 5G

06/26/2018 | Chang Fei Yee, Keysight Technologies
This article briefly introduces the 4-level pulse amplitude modulation (PAM-4) and its application in 400 Gigabit Ethernet (400GbE), to support the booming data traffic volume in conjunction with the deployment of 5G mobile communications. Furthermore, this article also highlights the essential pre-layout effort from signal integrity perspective for physical (PHY) link design on a PCB, including material selection, transmission line design and channel simulation to support 56Gbps data rate that paves the way for seamless communication in 400GbE.

Excerpt: The Printed Circuit Designer’s Guide to…Flex and Rigid-Flex Fundamentals

06/25/2018 | Dave Lackey and Anaya Vardya, American Standard Circuits
The design process is arguably the most important part of the flex circuit procurement process. The decisions made in the design process will have a lasting impact, for better or worse, throughout the manufacturing cycle. In advance of providing important details about the actual construction of the flex circuit, it is of value to provide some sort of understanding of the expected use environment for the finished product.



Copyright © 2018 I-Connect007. All rights reserved.